Contact Us

TPS7A0230PDBVR

Brand: Texas Instruments
Texas Instruments TPS7A0230PDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A0230PDBVR — Power Management & Signal Chain | Superb Automation

TPS7A0230PDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A0230PDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A0230PDBVR: 200 mA nanopower LDO, 3.0 V fixed output, 25 nA quiescent current

TPS7A0230PDBVR is a fixed 3.0 V linear regulator rated 200 mA with a quiescent current of 25 nanoamp in a SOT-23 body of 5 pins. The part is built for equipment that spends most of its life asleep: smoke detectors, meters, portable sensors and anything running from a coin cell. The quiescent current holds at 25 nanoamp even when the input has fallen to the output voltage, which is the case that usually ruins a sleep budget on an ordinary LDO.

Order code and package

TPS7A0230PDBVRActive, SOT-23-5, 3000 pieces on a large reel, NIPDAU or SN finish
TPS7A0230PDQNRActive, the 1 mm by 1 mm X2SON body, 3000 pieces on a large reel
TPS7A0230PDQNR in DSBGAActive, 12000 pieces on a large reel
TPS7A02 familyfixed outputs from 0.8 V to 5.0 V in 50 mV steps
Column cautionthe addendum prints the package column shifted by one row on this family, so the body has to be read from the suffix, DBV is SOT-23-5 and DQN is X2SON-4

Electrical parameters that decide the application

Input voltage1.5 V to 6.0 V
Output3.0 V fixed on this string, 200 mA
Quiescent current25 nanoamp typical, held in dropout as well
Shutdown current3 nanoamp typical
Dropout270 mV maximum at 200 mA for the 3.3 V option
Accuracy1.5 per cent over temperature
Transient responsesettling under 10 microsecond, 100 mV undershoot for a 1 mA to 50 mA step
Output capacitorstable with 1 microfarad or larger

Family variants and how they differ

X2SON DQN1.0 mm by 1.0 mm, four pins, no enable pin brought out
SOT-23 DBV2.9 mm by 1.6 mm, five pins, this order code
DSBGA YCH0.64 mm by 0.64 mm, the smallest body, 12000 pieces on a reel
Enable circuitinternal pulldown holds the part off when EN is left floating
Output options50 mV steps between 0.8 V and 5.0 V, so 3.0 V and 3.3 V are different order codes

Points to check before this part goes on a BOM

25 nanoamp has to be read against the load, not on its own. A 25 nanoamp quiescent current only matters when the load in sleep is also in the nanoamp range, which is true for a humidity sensor or a meter that wakes twice a day. Put a 1 milliamp always on load behind this regulator and the quiescent current stops being the reason to choose it, while the 270 mV dropout still is.

Holding the quiescent current in dropout is the unusual part. Most regulators quote their best figure at a comfortable input and then climb when the input falls toward the output. This one keeps the figure while the pass element is in dropout, which is exactly the end of discharge condition on a two cell alkaline pack. That is the sentence worth quoting to a customer who is chasing standby life.

The 3 nanoamp shutdown figure changes what a switch is worth. With 3 nanoamp in shutdown the enable pin becomes a real power saving control. On a part that leaks a microamp when disabled, an external load switch would be added to reach the same sleep current, and that switch costs board space and money. Here the enable pin does the job.

The smart pulldown removes a resistor and adds a behaviour. The part stays off when EN floats, so no pulldown is needed and no rail comes up unexpectedly during assembly test. It also means a board that relies on a floating enable to turn the rail on will never see the rail come up, which is a mistake seen often when a board is copied from a part without this feature.

1.5 per cent over temperature is not a reference grade figure. For a 3.0 V rail that is plus or minus 45 mV across the full range. If the rail is feeding an ADC reference or a bridge excitation, that error sits on the measurement. The part is right for a logic rail and for a sensor supply where the sensor is ratiometric to the same rail, not for an absolute reference.

The transient response number is the reason a small output capacitor is enough. A 1 mA to 50 mA step settles in under 10 microseconds with about 100 mV of undershoot. That is what allows a 1 microfarad ceramic instead of the 4.7 or 10 microfarad usually needed at this current. Keep the capacitor close to the pin or the trace inductance eats the advantage.

Ten packages in the same family means the suffix decides the board. DBV is the SOT-23-5 in this order code, DQN is the four pin X2SON, and the DSBGA is smaller again with a 12000 piece reel. All three are the same die. A purchasing substitution between them is not a drop in unless the land pattern was drawn for it, and the DQN body has no enable pin at all.

Read the addendum column shift carefully on this family. The package column is printed one row off in the packaging table. Anyone reading the body from that table alone will conclude the DBV string is an X2SON part. The suffix is the reliable field, and the vendor product page is the second opinion worth checking before a purchase order is raised.

The 3.0 V option is less common than 3.3 V and that matters for supply. Most stock in this family sits on the 3.3 V and the 1.8 V codes, so a 3.0 V requirement turns into a lead time problem at short notice. Where the rail tolerance allows it the 3.3 V part is easier to find on the same reel size. Where it does not, the 3.0 V string has to be placed early rather than substituted late, because a fixed output cannot be trimmed on the board.

Where a 25 nanoamp regulator earns its price

Battery powered sensors that sleep for hours and transmit for milliseconds: the average current is dominated by the sleep state, so the regulator rather than the radio sets the battery life.

Meters and detectors that must keep a real time clock and a small memory alive for years: the 3 nanoamp shutdown state and the 25 nanoamp running state both sit below the self discharge of the cells.

Where this order code fits

It keeps a 3.0 V rail alive in smoke and heat detectors, thermostats, motion detectors, water and electricity meters and cordless tool packs, where the sleep current sets the battery life. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Does it need a minimum load to stay in regulation? No. The part is stable from zero load, which is the point of the nanopower bias circuit. A regulator that needs a minimum load would waste exactly the current this part is chosen to save.

Can it be used at 5 V input with a 3.0 V output at 200 mA? Yes, but the dissipation is 400 mW and the SOT-23-5 has to get rid of it. At that point the junction rise in a warm enclosure is the limiting factor, not the current rating, and a larger body or a switching converter is the better answer.

What is the difference between the 30 and the 33 order codes? Only the fixed output voltage, 3.0 V against 3.3 V. The silicon, the package options and the reel sizes are the same, so they can be substituted on a board only if the rail tolerance allows it.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.