TPS79618DCQR
Product Specifications
TPS79618DCQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79618DCQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79618DCQR: 1.8 V, 1 A, in a six pin SOT-223
The TPS79618DCQR is the fixed 1.8 V member of the TPS796 family from Texas Instruments, a 1 A regulator in the six pin SOT-223 body coded DCQ. It ships 2500 pieces per reel at moisture level 2 with a one year floor life, marking PS79618, and it holds the output inside a plus or minus 2 percent window over the 0 A to 1 A load range with 1 V or more of input headroom.
Two points on this member are worth reading before it goes on a bill of material. First, the electrical table publishes dropout rows for the 2.8 V, 3.0 V, 3.3 V and 5.0 V points but not for 1.8 V, because the minimum input of 2.7 V governs the 1.8 V case and a 1.8 V rail never reaches the dropout limit on a 2.7 V input. Second, the SOT-223 body is the warmest of the three bodies in the family at 70.4 C per W on the legacy silicon, against 47.8 in the SON and 25 in the TO-263, so a 1 A rail at high dissipation belongs in a different package.
Key electrical data for the 1.8 V point
| Output voltage | 1.8 V fixed, plus or minus 2 percent over the load range |
| Output current | 1 A continuous, current limit 2.4 A to 4.2 A on the legacy silicon |
| Input range | 2.7 V to 5.5 V on the legacy silicon, 2.7 V to 6.0 V on the current one |
| Accuracy | 2 percent for the fixed points below 5 V, 3 percent for the 5.0 V point |
| Quiescent current | 265 uA typical and 385 uA maximum on the legacy silicon |
| Rejection and noise | 59 dB at 100 Hz and 10 mA, 54 dB at 1 A, 42 dB at 100 kHz, 41 uV RMS with 0.01 uF |
Package, marking and reel data
| Body | SOT-223 DCQ, 6 pins, tab soldered to the rail |
| Reel | 2500 pieces, large tape and reel |
| Finish and moisture | NIPDAU, level 2, 260 C, one year floor life |
| Marking | PS79618 |
| Thermal resistance | 70.4 C per W on the legacy silicon, 71.1 C per W on the current one |
Where a 1.8 V rail at 1 A belongs
1.8 V at 1 A is the supply of a dense digital subsection: a processor core, a DDR2 or LPDDR2 memory rail, an FPGA auxiliary supply or a set of high speed serialisers. In radio and instrumentation equipment it is also the rail behind a data converter bank, where the converter noise floor is set by the supply. The rejection and noise figures put this part in the middle of the family: good enough for a converter bank, not the quietest member for a reference chain.
The SOT-223 body is cheap and easy to solder, and it is also the limiting factor. At 70.4 C per W, 1 A from 2.5 V to 1.8 V is 0.7 W and a 49 degree rise, which is fine. From 3.3 V to 1.8 V the same current is 1.5 W and a 106 degree rise, which puts the junction near 150 degrees in a 45 degree enclosure and outside the 125 degree rating. From a 5 V bus the part cannot carry 1 A at all. Where the input is a 5 V or 12 V bus, the right answer is a switching stage followed by a linear regulator, not a bigger tab.
The 1.8 V point also has an input floor consequence that buyers miss. With a 2.7 V minimum input, a 2.5 V bus cannot supply this part at all, and a 3.3 V bus with 10 percent tolerance sits at 2.97 V, which is inside the rating but leaves only 1.17 V of headroom. That is enough for 1 A but the dissipation has to be checked rather than assumed.
Buyer questions on this order code
Why is there no dropout row for 1.8 V? Because the minimum input of 2.7 V is reached before the pass device saturates, so the dropout figure would never be the binding limit at 1 A. The number to use for this voltage is the input floor plus the load regulation.
Is the DCQ body the same as the DCQR order code? The addendum lists TPS79618DCQ and TPS79618DCQR, and the R marks the tape and reel. The bare code is the same part without the reel, which is why a line item should carry the R when the assembly house expects a reel.
Can the SOT-223 carry 1 A from a 3.3 V bus? At 1.5 W and 70.4 C per W the rise is about 106 degrees, so yes at a 25 degree ambient and no in a warm enclosure. The tab has to be soldered to a copper area, and a 45 degree ambient leaves very little margin.
Sourcing the TPS79618DCQR through SUPERB
SUPERB quotes the reel code rather than the bare part number, because the 2500 piece reel with the R suffix is what an assembly house can actually load. The PS79618 marking, the level 2 moisture bag and the date code are checked on receipt, and the certificate of conformance travels with the shipment.
When the dissipation does not fit the SOT-223, the power management cross reference page lists the bodies that carry more heat, and component lead time solutions covers the schedule side. Send the input bus, the load and the ambient and we answer with the body that fits.