TPS79601DCQR
Product Specifications
TPS79601DCQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS79601DCQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS79601DCQR: a 1 A ultra low noise RF low dropout regulator in SOT-223
TPS79601DCQR is an adjustable 1 A low dropout linear regulator in a SOT-223 (DCQ) body of 6 pins. The DCQ body is the 6.5 mm by 7.06 mm SOT-223 with six pins, and the 01 in the ordering string marks the adjustable member of the family, whose feedback pin is held at 1.225 V. The body is the one that carries heat, so it is the version chosen when a 1 A linear rail has to be dropped from 3.3 V to 1.8 V on a board without much copper.
Order code and package
| TPS79601DCQR | SOT-223 (DCQ), 6 pins, 3000 piece large reel, adjustable output |
| TPS79601DRBR | VSON (DRB), 8 pins, 3 mm by 3 mm body, same adjustable part |
| TPS79601KTTR | TO-263 (KTT), 5 pins, 10.16 mm by 15.24 mm, the highest dissipation body of the three |
| Fixed output members | the family covers fixed voltages alongside the 01 adjustable version, and the ordering string is the only place the setting appears |
| Finish and floor life | RoHS yes, with the reels carrying the standard level 1 rating at 260 C |
Electrical parameters that decide the application
| Input and output | 2.7 V in, 5.5 V maximum on the legacy chip and 6.0 V on the new chip, output from 1.225 V up to 5.5 V minus dropout |
| Current | 1 A continuous, with the internal current limit protecting the pass device |
| Reference | 1.225 V nominal, 1.2 V to 1.25 V window at the feedback pin |
| Accuracy | ±2 percent over 0 A to 1 A on the legacy chip, ±2.5 percent on the new chip |
| Noise | 54 uVrms on the legacy chip, 78 uVrms on the new chip, which is why the part is specified for RF and analog rails |
| Dropout | 220 mV typical at 1 A |
| Stability | stable with a 1 uF ceramic output capacitor, no tantalum required |
| Start-up | fast start-up with the noise reduction pin free to take a 0.01 uF capacitor on the legacy chip |
| Absolute maximum | 6.5 V on the new chip supply, 6 V on enable and output |
| Thermal | 70.4 to 71.1 C/W junction to ambient on the DCQ body, against 47.8 to 54.7 C/W on the DRB body |
Family variants and how they differ
| Legacy against new chip | the same ordering family exists in two silicon generations, with 54 against 78 uVrms of noise, 5.5 V against 6.0 V of maximum input and ±2 against ±2.5 percent of accuracy |
| DCQ against DRB | the SOT-223 carries the heat better in still air, the 3 mm VSON is the choice where the board has copper to spare but no height |
| KTT body | the TO-263 is the only one that will hold 1 A of linear drop without a thermal via field under it |
| The 01 suffix | adjustable, so the output is set by two resistors against the 1.225 V reference rather than fixed inside the part |
Points to check before this part goes on a BOM
The noise figure is the reason to pick this family over a general purpose 1 A regulator. 54 uVrms on the legacy chip and 78 uVrms on the new one, with high power supply rejection and a fast start-up, is what an RF or converter front end needs from the rail feeding its reference. A generic LDO with the same 1 A rating will regulate correctly and still put its own noise into the analog path.
Two silicon generations share the ordering family and the numbers differ, so the generation has to be established before a quote or a substitution. The legacy chip takes 5.5 V maximum and quotes 54 uVrms and ±2 percent, the new chip takes 6.0 V and quotes 78 uVrms and ±2.5 percent. Both are in the same bodies, and the pin functions differ slightly between the two on the sixth pin, which is either a noise reduction capacitor connection or the feedback pin depending on the generation.
Linear dissipation is the practical limit at 1 A. Dropping 3.3 V to 1.8 V at 1 A burns 1.5 W in the pass device, and the DCQ body at 70.4 C/W needs a copper pad and airflow to hold that. The DRB body at 47.8 C/W is better on a board with an internal ground plane, and the TO-263 is the one to use when the drop and the current both stay at their maximum.
The 220 mV dropout at 1 A leaves a 2.7 V input able to hold about 2.5 V at the output, which is the number to check before specifying a 2.5 V rail from a 3.3 V bus with a long trace. The input floor of the part is 2.7 V, so a 3.3 V supply that sags by 300 mV under load stays inside the window; a 3.0 V supply does not.
Choosing a body for a 1 A linear rail
The three bodies carry the same die and differ in how much heat they can pass to the board. SOT-223 at 70.4 C/W, 3 mm VSON at 47.8 C/W and TO-263 as the outlier for the heaviest drop. On a 1.5 W dissipation the difference between the first two is about 20 C of junction temperature, which is often the difference between a part that runs at its limit and one that has margin.
The 1 uF ceramic stability requirement makes the output capacitor choice simple and removes the tantalum that older 1 A regulators needed. It also means the capacitor voltage rating and the temperature coefficient are the only remaining decisions, and an X5R part at twice the rail voltage covers both.
A last check belongs on the enable pin. The part is enabled by a logic high on EN, and the pin has to be defined before the input rail comes up, or the output follows the input through the pass device during the ramp. A 100 kOhm pull down to ground settles that without loading the controller's logic output, and it is the first thing to check when a board comes back with the rail present before the controller has finished its own reset.
Where this order code fits
It feeds RF and analog sections, TV and set top box rails, building automation controllers and connected peripherals, anywhere a quiet 1 A rail has to come from a noisier bus. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Which chip generation is the DCQR? Both generations exist in the DCQ body and the ordering string does not spell out which one is inside, so the generation is confirmed against the vendor's addendum before a quote. The two differ in maximum input, noise and accuracy, so the answer changes what the part can be used for.
Is the output adjustable? Yes, the 01 suffix is the adjustable member. The output is set by two resistors against the 1.225 V reference, so the same part covers any rail from 1.225 V up to 5.5 V minus the dropout.
What does it need on the output? A 1 uF or larger ceramic capacitor. The part is stable with ceramic and does not need the tantalum that older 1 A regulators required, which is one of the reasons it is still specified on RF boards.
How much heat at 1 A? Dissipation is the input minus output voltage times the current. Dropping 3.3 V to 1.8 V at 1 A is 1.5 W, which the DCQ body at 70.4 C/W can hold only with a copper pad under it and some airflow.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.