Contact Us

TPS79501QDRBRQ1

Brand: Texas Instruments
Texas Instruments TPS79501QDRBRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS79501QDRBRQ1 — Power Management & Signal Chain | Superb Automation

TPS79501QDRBRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS79501QDRBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS79501QDRBRQ1: a 500 mA adjustable low noise regulator in a 3 mm by 3 mm body, with 110 mV of dropout and two silicon generations behind one part number

TPS79501QDRBRQ1 is a linear regulator that takes a noisy 5 V or 3.3 V rail and delivers a quiet adjustable output for an analogue or radio stage, with the noise and rejection figures of a purpose built part rather than a general purpose regulator in a VSON body of 8 pins. The DRB body is eight pins on 3.00 mm by 3.00 mm, and the same die is offered in a six pin SOT-223 for boards that need the larger thermal footprint.

Order code and package

Catalogue stringTPS79501QDRBRQ1, where 01 is the adjustable member and the Q1 suffix is the automotive marker carried by the page title
BodyVSON, DRB, eight pins, 3.00 mm by 3.00 mm, with a six pin SOT-223 DCQ alternative at 6.50 mm by 7.06 mm
Reel3000 pieces on a large tape and reel for the DRBR row, 250 pieces for the DRBT row, and 2500 pieces for the SOT-223 DCQR row
Finish and moistureNIPDAU plating, moisture level 2, 260 C, one year floor life
Temperatureminus 40 to 125 C junction on the current rows
MarkingBUH on the DRB body
DocumentSLVS350L, October 2002, revised January 2026
Order code checkthe addendum in this revision prints no Q1 row for any member of the family, so the automotive suffix in the title is not covered by the document that describes the part

Electrical parameters that decide the application

Input rangeup to 5.5 V, with the dropout specified at an input one volt above the nominal output
Outputadjustable from 1.225 V to 5.5 V minus the dropout, set by an external divider against a 1.225 V reference that holds between 1.200 V and 1.250 V
Output current500 mA, and the specification is written at that current rather than at a fraction of it
Dropout110 mV typical and 170 mV maximum at 500 mA, so a 3.3 V output needs 3.47 V of input at full load
Accuracyplus or minus 2 per cent on the legacy silicon and minus 2.5 to plus 2 per cent on the current silicon, both over the full load range
Noise33 uV RMS on the legacy chip and 78 uV RMS on the current chip, measured over 10 Hz to 100 kHz
Rejection50 dB at 10 kHz, which is the figure that matters when the input is a switching regulator running at a few hundred kilohertz
Ground current265 uA typical and 385 uA maximum on one generation, 500 uA typical and 900 uA maximum on the other, which is the price of the noise performance
Current limit2.4 A minimum and 4.2 A maximum at a 500 mA rating, with a short circuit current of 1.04 A to 1.65 A, so the part survives a faulted output
Output capacitorstable with 1 uF of ceramic, and the reference bypass capacitor on the legacy chip is 0.01 uF
Reference bypassthe noise reduction pin exists on the legacy silicon and is a no connect on the current silicon, which is how the two chips are told apart on a board
Thermal500 mA at 5 V in and 1.225 V out is 1.9 W in the pass element, which no 3 mm body survives, so the input to output difference is the first thing to check

Fixed members, adjustable member and the rows on the way out

TPS79501DRBRthe adjustable member, 3000 pieces large reel, marking BUH, and the row this page describes
TPS79501DCQRthe same die in SOT-223, 2500 pieces, for a board that needs the larger tab
TPS79501DCQthe tube row, 78 pieces, which is the prototype quantity
TPS79516 and TPS79518the fixed 1.6 V and 1.8 V members, and the addendum prints the DCQ rows as Obsolete, so those voltages are lapsing
TPS79525 and TPS79530 and TPS79533the fixed 2.5 V, 3.0 V and 3.3 V members, which stay in production and remove the divider and its tolerance
TPS7A90the family the vendor points to as the newer alternative, worth checking before a long life build is committed

Points to check before this part goes on a BOM

Two silicon generations share this part number and they do not have the same noise. The legacy chip is 33 uV RMS with a noise reduction pin and a 0.01 uF bypass capacitor on it, and the current chip is 78 uV RMS with that pin turned into a no connect. Both are specified at 500 mA and both are sold under the same order code in some rows. A board that was qualified for a radio sensitivity budget on the legacy chip is 7.5 dB worse on noise if the current chip lands, which is the sort of change that shows up as a shorter range rather than as a failure.

The Q1 suffix in the page title is not covered by the document that describes the part. The addendum prints TPS79501DRBR and its G4 and .A rows, all Active, all in the same body and reel, and it prints no automotive row at all. That does not mean the automotive part does not exist, because the automotive family has its own documents, but it does mean a quotation that cites this revision as the source of an automotive row is citing something the revision does not contain. The suffix should be confirmed against a customer purchase order or against a dedicated automotive document before a line is committed.

The fixed members are the better buy where the voltage is one of them. A fixed 3.3 V part needs no divider, so the output accuracy is the regulator's own 2 per cent rather than 2 per cent plus two resistor tolerances plus the reference pin current. The adjustable member exists for the rails that no fixed option covers, and a divider on it should use 1 per cent resistors and a lower leg small enough that the 1 uA of reference pin current does not tilt the ratio.

The dropout figure has a condition attached that is easy to lose. 110 mV typical at 500 mA is measured at an input one volt above the nominal output. At 5 V in and 3.3 V out the pass element is dropping 1.7 V at 500 mA, which is 850 mW in a 3 mm body with a thermal resistance in the tens of degrees per watt. That is a part running very hot, and the honest answer for that combination is either a lower input voltage or a switching regulator ahead of it. A 500 mA linear regulator is a quiet way to make a rail and a poor way to drop two volts.

The current limit window runs from 2.4 A to 4.2 A on a 500 mA part, which is a fold back limit rather than a precise one. A load that draws 600 mA for a moment will not be limited, and a short will pass 1.04 A to 1.65 A continuously until the thermal shutdown acts. That is enough to protect the regulator and not enough to protect a connector, so a rail that leaves the board still needs its own protection. Inside a board, the limit is there so a faulted analogue stage does not take the whole rail down.

The 3.3 V and 3.0 V fixed members share a body and a pinout with the adjustable one, so a change between them is a change of divider and nothing else. That is the cheapest way to remove a tolerance term late in a programme, and it is also the cheapest way to introduce a mistake, because the divider pads stay on the board and a stuffed upper resistor on a fixed part changes nothing while a missing one on an adjustable part gives 1.225 V where 3.3 V was expected.

Matching the noise figure to the radio

78 uV RMS over 10 Hz to 100 kHz sounds small and is large for a receiver front end. A low noise amplifier with a 1 dB noise figure and 20 dB of gain is not disturbed by 78 uV of supply noise; a mixer or a voltage controlled oscillator running from the same rail is. The rule that works is to look at the phase noise sensitivity of the stage rather than at the regulator, and to put the regulator's rejection curve on the same graph as the stage's supply sensitivity.

The two chips make that graph look different below 1 kHz and above 10 kHz. The legacy chip at 33 uV RMS total has most of its noise at low frequency, and the current chip at 78 uV RMS has a flatter distribution. A stage that is sensitive at 100 Hz cares about the first, and a stage sensitive at 1 MHz, where both parts have fallen off, cares about neither. That is why the rejection figure at 10 kHz is quoted alongside the total noise: it is the number that predicts what a switching regulator in front of the linear part will leave behind.

Reading an obsolete row before it becomes a shortage

The fixed 1.6 V and 1.8 V members print Obsolete on the DCQ rows in this revision, which means the vendor has stopped building them in that body. A board that uses one of those voltages has three routes: move to the adjustable member and set the voltage with a divider, move to the DRB body if a row survives there, or buy the remaining stock and plan a last time buy. The first route costs two resistors and a re-qualification of the output tolerance, and it is usually the cheapest.

The earlier a lapsing row is spotted, the less it costs. A last time buy sized on two years of demand ties up cash and shelf life, and a respin started six months before the last shipment is a normal programme rather than an emergency. The signal to watch is the status column in the addendum, not the distributor stock count, because a part that is Obsolete can still be plentiful on the shelf for a year.

Where this order code fits

This is the post regulator behind a switching supply on a radio board, a data converter supply, an audio stage or a measurement front end, where the rail has to be quiet rather than efficient Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Is 110 mV of dropout real at 500 mA? It is the maximum load figure with the input one volt above the output, and 170 mV is the guaranteed limit. A 3.3 V output therefore needs 3.47 V of input to stay in regulation.

Why do two parts with the same number have different noise? There are two silicon generations. The legacy chip is 33 uV RMS with a noise reduction pin, the current chip is 78 uV RMS with that pin unconnected, and only the marking and the board tell them apart.

Does the order code cover an automotive part? Not in this revision. The addendum prints no Q1 row for the family, so the suffix in the title has to be confirmed against a purchase order or a separate automotive document.

Can it drop 5 V to 1.225 V at 500 mA? It can conduct that current and it cannot dissipate the 1.9 W. The pass element in a 3 mm body has a thermal limit in the tens of degrees per watt, so that combination needs a switching stage ahead of it.

What output capacitor does it need? 1 uF of ceramic is enough for stability, which is unusual for a part of this age and is the reason it still appears on new boards.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Last-Time-Buy and LTB Planning page sets out the checks that keep a substitute from failing on the bench.