TPS78550QKVURQ1
Product Specifications
TPS78550QKVURQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS78550QKVURQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS78550QKVURQ1 automotive 5 V 1 A regulator in the TO-252 body
The TPS78550QKVURQ1 is the 5.0 V fixed member of the TPS785-Q1 family in the five lead TO-252 body, ordered on a 3000 piece reel. It sources 1 A from an input between 1.7 V and 6.0 V with 0.5 per cent typical and 1.7 per cent maximum accuracy, 25 microamp of quiescent current, 50 dB of rejection out to 100 kHz and 315 mV of maximum dropout at 1 A on the 3.3 V member. The TO-252 body is the reason the part exists at this current: the tab is the heat path, and a 1 A rail in a module with a 5 V bus needs one.
The 5.0 V output from a 6.0 V ceiling leaves a volt of headroom, which is enough for the dropout and not enough to waste. At 1 A the dissipation is 1 W when the input sits at 6 V, and the TO-252 tab soldered to a copper area spreads that into the board rather than into the air around a small package. Internal soft start of 550 microseconds limits the inrush, foldback current limit reduces the dissipation during a short, and the active output discharge pulls the rail down when the enable goes low.
Key parameters printed in the SBVS388B document
| Output | 5.0 V fixed, with 0.65 V to 5.0 V members in the family |
| Input range | 1.7 V to 6.0 V |
| Load current | 1 A |
| Accuracy | 0.5 per cent typical, 1.7 per cent maximum over the operating range |
| Quiescent current | 25 microamp typical |
| Dropout | 315 mV maximum at 1 A on the 3.3 V member |
| Rejection and soft start | 50 dB out to 100 kHz, internal soft start of 550 microseconds |
| Protection | Foldback current limit, thermal shutdown, active output discharge on disable |
Package, reel and top side marking
| Package | TO-252, KVU body, five leads, tab as the heat path |
| Reel | 3000 pieces on a large tape and reel |
| Finish and moisture | Nickel palladium gold on the KVU rows, moisture level 2 with a one year floor life |
| Temperature and marking | Minus 40 to plus 150 degrees junction, top side marking 8550QKVU |
Where a TO-252 linear 5 V rail fits
A 5 V rail at 1 A in an automotive module is usually derived from a switcher and then cleaned by a linear stage, because the loads on it are a CAN transceiver, a sensor cluster and a microcontroller that all dislike switching ripple. The 5.0 V fixed member takes a 6 V intermediate bus and drops a volt, which is the smallest dissipation in the family at this current, and the TO-252 tab keeps the junction inside the rating at 1 W without a heatsink. Where the 5 V rail feeds logic that has to be present while the rest of the module is off, the 25 microamp quiescent current is what makes a permanent connection to the battery acceptable.
The order code needs one check before a purchase order. In the SBVS388B addendum the KVU rows print the package, quantity and marking of the DRB row beside them, so the line carrying this code shows a 2500 piece quantity that belongs to the eight pin body. The KVU row is 3000 pieces on a large reel with the marking 8550QKVU, and the moisture level is level 2 on one row and level 3 on the row printed beside it. That is the kind of detail that only surfaces when a store rejects a delivery, and the date code management page describes how SUPERB matches the reel label to the addendum row before the parts reach the line.
Questions buyers ask before ordering
Does the tab have to be soldered? Yes if the part is to run at 1 A. The tab is the heat path, and a tab left unsoldered turns 1 W into a junction temperature the package was never meant to hold.
Can it run from a 5.5 V input? It can, but the margin above a 5.0 V output is 500 mV, which is more than the 315 mV maximum dropout of the 3.3 V member and close to the limit at temperature; a 6 V bus is the intended arrangement.
Why does the addendum print two moisture levels? The columns of the KVU and DRB rows are interleaved in one table. The row for this code is level 2 with a one year floor life, and the level 3 line belongs to the body printed beside it.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line, confirms the body, the reel quantity and the moisture level from the code rather than from the printed line, and keeps the certificate with the reel. Send the rail, the load and the input bus through the supplier quality audit page when the program needs the traceability record with the parts, and the answer comes back with the code, the reel and the date code.