Contact Us

TPS78222DRVR

Brand: Texas Instruments
Texas Instruments TPS78222DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS78222DRVR — Power Management & Signal Chain | Superb Automation

TPS78222DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS78222DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS78222DRVR: a 150 mA regulator with a 500 nA quiescent current and a 2.2 V fixed output

TPS78222DRVR is a linear regulator built for the gap between a cell and a microcontroller, holding a 2.2 V rail while drawing half a microamp when nothing is running in a WSON body of 6 pins. The DRV body is six pins on a 2 mm by 2 mm pad, and the number 22 in the code is the fixed 2.2 V output, which is the rail a low power microcontroller or a radio front end wants when it has to run from a single cell down to 2.5 V.

Order code and package

Catalogue stringTPS78222DRVR, the DRV body with the R reel letter
BodyWSON, six pins, DRV, 2.00 mm by 2.00 mm, with the five pin TSOT-23 DDC body as the alternative
Reel3000 pieces on a large tape and reel for the plain and G4 rows, while the DRVT row and the G4.A row print 250 pieces on a small reel
Finish and moistureNIPDAU or NIPDAUAG plating, moisture level 1, 260 C, unlimited floor life
Temperatureminus 40 to 125 C junction
MarkingRAR
DocumentSBVS115D, revised January 2015
Enable pinCMOS compatible, so a 1.8 V logic output turns it on without a level shift

Electrical parameters that decide the application

Input range2.2 V to 5.5 V, which is a single lithium cell plus a little headroom
Output2.2 V fixed on this code, with the family covering 1.8 V to 5 V in 100 mV steps and a few odd values
Output current150 mA maximum, with the accuracy specified across the whole range rather than at one point
Quiescent current500 nA headline, with a ground pin current of 0.42 uA typical at no load and about 15 uA at 150 mA
Shutdown current40 nA typical and 130 nA maximum with the enable pin below 0.4 V, which is what makes a battery shelf life measurable
Accuracyplus or minus 3 per cent over line, load and temperature, and plus or minus 1 per cent at 25 C
Dropout at 25 C130 mV at 150 mA, so a 2.2 V output needs 2.33 V at the input
Dropout at 85 C175 mV at 150 mA, which is the number to use for a product that runs warm
Line regulation1 per cent over the input range at 5 mA of load
Load regulation1 per cent from 0 to 150 mA
Current limitabout 400 mA, which is roughly 2.7 times the rated load and enough to survive a short at the connector
Output capacitor1.0 uF ceramic, stable with a small ceramic and no ESR requirement
Ripple rejectionabout 40 dB at low frequency and 20 dB at higher frequency, adequate for a rail that feeds a sleeping processor
Thermal shutdowninternal, with the current limit as the first line of defence on a fault

Fixed codes and the rows that differ only by suffix

TPS78222DRVRthe 2.2 V rail on the 3000 piece large reel, the row this page describes
TPS78222DRVTthe same device on a 250 piece small reel, for a first article or a repair batch
TPS78222DRVRG4the green material row, 3000 pieces
TPS78222DRVRG4.Athe revision letter row, which the addendum prints at 250 pieces even though the plain G4 row is 3000, a difference worth catching before an order is placed
TPS78233the 3.3 V member of the same family, same body and same current
TPS780the same quiescent current with dual level voltage scaling, for a processor that switches between two rails

Points to check before this part goes on a BOM

The 500 nA headline and the 0.42 uA ground current are the same measurement described two ways. At no load the part draws 0.42 uA typical, which rounds to 500 nA, and at 150 mA it draws about 15 uA because the pass FET gate has to be driven harder. A budget that multiplies 500 nA by the duty cycle and ignores the loaded figure understates the consumption of an awake rail by a factor of thirty.

A 2.2 V output from a 2.2 V minimum input is not a regulator, it is a switch. The 130 mV of dropout at 150 mA means the input has to stay above 2.33 V for the output to hold, and a single cell crosses that point at about 20 per cent state of charge. Below it the part follows the input down, which is graceful and still outside specification. A product that needs 2.2 V down to 2.0 V needs a different part, not a different capacitor.

The suffix rows on this family are not uniform. The plain DRVR and the G4 row are 3000 pieces, and the DRVT row and the G4.A row are 250 pieces. Four strings that look like the same part in four packing variants are two reels and two small reels, and the difference matters on a line that plans a full reel per shift. This is the sort of thing that should be fixed on the offer rather than discovered at the feeder.

The dropout figure moves with temperature and the data sheet gives both numbers. 130 mV at 25 C and 175 mV at 85 C, on the same 150 mA load. A board that budgets the 25 C figure and then runs at 70 C inside a sealed enclosure has 45 mV less headroom than it planned for, which on a 2.2 V rail is 2 per cent of the rail. The 85 C number is the one to sign off against.

1 uF of ceramic on the output is the entire external component count besides the input capacitor. That is the point of the part: a two by two millimetre body with one capacitor per side fits in the space a module has left after the radio and the antenna. The stability with a small ceramic is what makes that possible, and it is why a 4.7 uF capacitor is not needed and adds nothing but board area.

The enable pin is CMOS compatible and that is a feature rather than a footnote. A 1.8 V logic output from a microcontroller can drive it directly without a level shifter, and the pin draws 8 nA, so the microcontroller does not have to source current to keep the rail on. On a board where every microamp is counted, that matters as much as the quiescent current of the regulator itself.

What 150 mA buys and what it does not

150 mA at 2.2 V is 330 mW of output, which covers a microcontroller in run mode, a low power radio during transmit, a small display and a handful of sensors. It does not cover a flash write plus a radio transmit at the same time, which is the moment a product runs out of current and the rail sags. The current limit at 400 mA protects the part, and the 175 mV of dropout at 85 C decides whether the sag reaches the load.

The package is the other half of the answer. A 2 by 2 mm body with no thermal pad has a junction to ambient resistance in the hundreds of degrees per watt, so the dissipation has to stay small. 150 mA through a 175 mV dropout is 26 mW, which raises the junction by a few degrees. A 5 V input with a 2.2 V output is 2.8 V across the pass FET, which at 150 mA is 420 mW and is not survivable. The part is built for a cell, not for a 5 V rail with a low output.

Reading the ground current curve correctly

The ground current curve is flat from zero to full load and then rises at the top end, which is the signature of a low quiescent current regulator with a weak pass FET drive. On this part it stays near 0.42 uA until a few milliamps and reaches about 15 uA at 150 mA. That shape is what makes the part good for a load that is asleep ninety nine per cent of the time and merely adequate for a load that runs continuously.

The comparison that matters is against a regulator with a 50 uA quiescent current. On a rail that draws 100 uA average, the 50 uA part wastes a third of the energy and this one wastes half a per cent. On a rail that draws 100 mA average, the difference is invisible. Choosing a low quiescent current part only pays on rails that are actually idle, and paying for one on a busy rail buys nothing but a slightly worse transient.

Where this order code fits

This is the rail behind a low power microcontroller, a sub gigahertz radio, a sensor node or a handheld instrument, where the product sleeps for weeks and the cell has to survive it Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Is the quiescent current really 500 nA? At no load, yes, with 0.42 uA typical and the shutdown current at 40 nA. At 150 mA the ground current rises to about 15 uA, so the loaded figure is thirty times the headline.

Can it hold 2.2 V from a single cell? Down to about 2.33 V at 150 mA and 25 C, and about 2.38 V at 85 C. Below that the output follows the input down, so the usable cell range ends near 20 per cent state of charge.

Which order code is the large reel? TPS78222DRVR and TPS78222DRVRG4 are 3000 pieces. The DRVT and the G4.A row are 250 pieces on a small reel, even though the strings look like packing variants of the same part.

What output capacitor is needed? 1.0 uF of ceramic. The part is stable with a small ceramic and does not need a specific ESR, which is what keeps the external count at one capacitor per side.

Does it have thermal protection? Yes, thermal shutdown plus a current limit at about 400 mA. The current limit acts first on a short, and the shutdown covers a thermal fault.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Safety Stock Planning page sets out the checks that keep a substitute from failing on the bench.