Contact Us

TPS78218DRVR

Brand: Texas Instruments
Texas Instruments TPS78218DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS78218DRVR — Power Management & Signal Chain | Superb Automation

TPS78218DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS78218DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS78218DRVR: 150 mA LDO with a 500 nA quiescent current for rails that sleep

TPS78218DRVR is an ultra low quiescent current linear regulator for a 1.8 V rail that has to last on a small cell in a SOT-23 thin body of 5 pins. It holds 1.8 V at up to 150 mA from a 2.2 V to 5.5 V input and draws 500 nA with no load, which is what makes it usable on a rail that is alive for months. Dropout is 130 mV at full load and 25 C, rising to 175 mV at 85 C, and the output is stable with a 1 uF ceramic capacitor.

Order code and package

TPS78218DRVR5 pin SOT-23 thin (DDC), 3000 pieces on a large reel, marking SAF
TPS78218DDCRthe same silicon in the other 5 pin body, 3000 pieces on a large reel
TPS78218DRVT6 pin WSON body, the smaller footprint option, 250 pieces on a small reel
Output voltage1.8 V fixed, trimmed in the factory, no divider
Quiescent current500 nA typical with no load, which is the figure the part is sold on

Electrical parameters that decide the application

Input voltage range2.2 V to 5.5 V, so a single cell works across most of its discharge curve
Output current150 mA continuous
Output voltage1.8 V fixed on this row, the family covers 1.2 V to 3.3 V in fixed steps
Dropout voltage130 mV at 150 mA and 25 C, 175 mV at 150 mA and 85 C
Accuracy3 per cent over load, line and temperature
Quiescent current500 nA typical, the reason the part exists
Output capacitor1 uF ceramic, stable across the load range
Enable pina logic input, so the rail can be switched off without a load switch
Temperature rangeminus 40 C to plus 125 C

Where the fixed output rows sit

TPS782181.8 V fixed, the row on this page, for a memory or a low power processor rail
TPS782222.2 V fixed, for a radio or a sensor that wants a little more headroom
TPS78225 and TPS782282.5 V and 2.8 V fixed, the common sensor and peripheral rails
TPS78230 and TPS782333.0 V and 3.3 V fixed, for a module or a microcontroller
DDC body5 pin SOT-23 thin, 1.12 mm tall, the easiest package to inspect
DRV body6 pin WSON, smaller footprint, needs a paste stencil matched to the pitch

Points to check before this part goes on a BOM

The 500 nA quiescent current is the specification that matters and the one that is easiest to lose. It applies with the part enabled and no load, and it is measured at a specific input voltage. Any added divider on the output, any pull up that is left connected, and any leakage path will swamp 500 nA, and a rail that measures 20 uA at no load usually has a 20 uA resistor network somewhere rather than a bad regulator.

Dropout of 130 mV at 150 mA is comfortable on a 3.3 V to 1.8 V rail and tight on a 2.2 V to 1.8 V rail. At the bottom of the input range there is 400 mV of headroom, and the dropout rises with temperature to 175 mV, so the regulation holds but the margin shrinks. A product that runs from a cell to 2.2 V and expects 1.8 V out is asking the part to work at 20 per cent of its headroom, which is where the accuracy figure starts to move.

The enable pin is a real advantage on a battery product because it removes a load switch from the bill of materials. The rail goes to zero when the pin is low, the part draws almost nothing, and the load is disconnected without an extra FET. What it does not do is discharge the output, so a rail with a large capacitor downstream stays up for a while after the enable goes low and a processor that expects a fast power down will not get one.

A 3 per cent accuracy figure is loose by the standards of a modern regulator and is the trade for 500 nA. The reference inside a part that draws half a microamp cannot be as sharp as one in a part that draws 50 uA, and the vendor is honest about it. On a 1.8 V rail 3 per cent is 54 mV, which is fine for memory and marginal for a radio that needs a tight supply.

The output capacitor requirement is modest, 1 uF ceramic, and that is deliberate: a part this low power is usually paired with a small ceramic and nothing else. The stability does not depend on ESR, so a 1 uF X5R in an 0603 works, and the only caution is that the capacitor's own leakage becomes part of the no load current once the rail is up.

Two 5 pin bodies are offered and they are not identical in handling. The DDC body is 1.12 mm tall and easy to inspect under a microscope, the WSON body is smaller and needs a stencil with a tight aperture. A program that second sources between them without checking the land pattern will find the pads do not match, and this is one of the few places on the line where the two order codes are genuinely different boards.

This is a mature part and it appears on the vendor list in fixed steps only, which means a rail that is not 1.2, 1.5, 1.8, 2.2, 2.5, 2.8, 3.0 or 3.3 V cannot be served by it. When a customer asks for an adjustable version, the answer is a different family, and offering this one as a substitute for an adjustable part is how a board ends up with the wrong rail.

Sourcing is straightforward while the part is active, and the family has been in production long enough that several fixed rails are stocked by distribution rather than made to order. The risk on a part this old is counterfeit material in the broker channel rather than allocation, so a purchase on this line should come with a date code and a traceable lot, and the 500 nA current is easy enough to measure that a sample check on a curve tracer or a source meter will expose a re marked part.

Where this order code fits

It keeps a 1.8 V rail alive in a product that spends most of its life asleep: utility meters, medical monitors, wireless sensors and battery powered instruments where the standby current is the specification the customer sells on. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

How low is the quiescent current really? 500 nA typical with no load, which is low enough that a 1 uF output capacitor's leakage and any divider on the rail can be larger than the regulator itself.

Can it run from a single lithium cell down to 2.2 V? Yes, and it stays in regulation at 1.8 V out, but the headroom falls to 400 mV against a 175 mV dropout at 85 C.

Is the output adjustable? No. This order code is fixed at 1.8 V, and the family covers other fixed rails only.

What capacitor does it need? 1 uF ceramic or larger, with no ESR requirement. The part is stable with ordinary X5R and X7R parts.

Does the enable pin discharge the output? No. The rail falls at whatever rate the load and the output capacitor allow, so a fast power down needs a discharge path.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.