TPS77801PWPR
Product Specifications
TPS77801PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS77801PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS77801PWPR 750 mA adjustable regulator with a power good flag
The TPS77801PWPR is the adjustable member of the TPS778 family in the 20 pin HTSSOP body with a thermal pad, ordered on a 2000 piece reel. Output is set by an external divider anywhere from 1.2 V to 5.5 V, the part sources 750 mA with 260 mV of typical dropout on the 3.3 V point, and the flag pin carries an open drain power good output rather than a reset. Quiescent current is 85 microamp typical and the loop is stable with a 10 microfarad low ESR output capacitor.
The adjustable version exists so one order code covers several rails. A board that needs 1.2 V for a core, 1.8 V for a memory bank and 3.3 V for a peripheral can carry the same part and change two resistors, which keeps the approved vendor list short and the second source question simple. The trade is accuracy: the 2 per cent device figure is on the reference, and the divider tolerance adds to it, so a 1 per cent resistor pair is normal on a rail where the load is sensitive to the set point.
Key parameters printed in the SLVS230G document
| Output | 1.2 V to 5.5 V adjustable from an internal reference with two external resistors |
| Load current | 750 mA |
| Dropout | 260 mV typical at 750 mA on the 3.3 V member of the family |
| Accuracy | 2 per cent on the device, with the divider tolerance added on the adjustable member |
| Quiescent current | 85 microamp typical across the load range |
| Current limit | 1.2 A typical, 2 A at the top of the band |
| Rejection and noise | 60 dB at 1 kHz, 54 microvolt RMS over 100 Hz to 100 kHz |
| Flag | Open drain power good, released when the output is inside tolerance |
Package, reel and top side marking
| Package | HTSSOP, PWP body, 20 pins, exposed thermal pad |
| Reel | 2000 pieces on a large tape and reel for the PWPR row, 70 pieces in a tube for the plain PWP row |
| Finish and moisture | Nickel palladium gold, moisture level 2, one year floor life on the reel row |
| Temperature and marking | Minus 40 to plus 125 degrees, top side marking PT77801 |
Where one adjustable code covers several rails
This code belongs on a platform board that has to serve several products, where the rails differ between variants and the bill of materials should not. It also suits a rail that has to be trimmed late in a program, because the divider can change without a new part number or a new reel. The power good flag then feeds a sequencer that does not have to know the rail voltage, only whether it is up, which is the property that makes a single regulator usable across a product family.
Two numbers decide whether the adjustable member is safe at the rail in question. The first is the minimum output, 1.2 V, below which the reference cannot be scaled; a 0.9 V core needs a different part. The second is dissipation, which rises as the output falls from a fixed input, so the same 750 mA from 3.3 V is 1.35 W at 1.5 V and 2.4 W at 1.2 V, and the 20 pin pad is the reason the higher figure is still possible. The how to verify a drop-in replacement page covers what has to be re-measured when the divider changes the rail.
Questions buyers ask before ordering
Can the output be set below 1.2 V? No. The reference sets a 1.2 V floor on this member, and a lower rail needs a part with a lower reference rather than a different divider.
Does the flag track the divider? It watches the regulated output, so it follows whatever the divider sets. It does not need to be re-trimmed when the rail changes.
What divider accuracy should be used? One per cent resistors are the practical choice. The device is 2 per cent, so a 5 per cent divider would dominate the error at the set point, and a pair of 0.1 per cent parts is only worth it when the rail is a reference for a converter.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line, confirms the divider values against the rail the customer names, and quotes the row that matches the packaging on the drawing. The one case where the adjustable member is the wrong choice is a rail whose set point is written into a safety file, because the divider then becomes a controlled item and every resistor change is a document change. Send the rails, the currents and the target date through the strategic sourcing page and the answer comes back with one code that covers the family of rails and the reel that goes with it.