Contact Us

TPS77515DR

Brand: Texas Instruments
Texas Instruments TPS77515DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS77515DR — Power Management & Signal Chain | Superb Automation

TPS77515DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS77515DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS77515DR 500 mA 1.5 V regulator with a reset output

The TPS77515DR is the 1.5 V fixed member of the TPS775 family in the eight pin SOIC body, ordered on a 2500 piece reel. It sources 500 mA with a typical dropout of 169 mV on the 3.3 V member of the family, holds 2 per cent tolerance over the specified conditions, and adds an open drain reset output with a 200 millisecond delay, which is the feature that separates this family from the plain regulators beside it on a bill of materials. Quiescent current is 85 microamp typical across the whole load range.

The reset comparator trips when the output falls to 92 to 98 per cent of its nominal value, with 0.5 per cent of hysteresis to stop it chattering, and it stays valid as long as the input is above 1.1 V. That last figure matters in a brown out: the reset output still asserts while the input collapses, so the processor is held in reset before its own supply reaches the point where it would behave unpredictably. The loop is stable with a 10 microfarad low ESR output capacitor, which is the value the transient response is specified against.

Key parameters printed in the SLVS232J document

Output1.5 V fixed, with fixed members from 1.5 V to 3.3 V and an adjustable member in the family
Load current500 mA
Dropout169 mV typical at 500 mA on the 3.3 V member of the family
Accuracy2 per cent over the specified conditions
Quiescent current85 microamp typical over 0 mA to 500 mA
Current limit1.2 A typical, 1.6 A maximum, 1.9 A at the top of the band
Rejection60 dB at 1 kHz with a 10 microfarad output capacitor
ResetOpen drain, 200 millisecond delay, trip at 92 to 98 per cent of output, valid above 1.1 V of input

Package, reel and top side marking

PackageSOIC, D body, eight pins
Reel2500 pieces on a large tape and reel, 75 pieces in a tube for the plain D row
Finish and moistureNickel palladium gold, moisture level 1, unlimited floor life
Temperature and markingMinus 40 to plus 125 degrees, top side marking 77515

Where an integrated reset saves a supervisor

The 1.5 V member is used where a memory or an FPGA auxiliary rail needs a clean supply and the board has no room for a supervisor. Because the reset output is open drain and the delay is internal, the only external part is a pull up, and the same signal can hold several devices in reset at once. On a 3.3 V input the dissipation at full load is 900 mW, which the SOIC body holds with a copper pour but not in still air on a small pad, so the copper area is part of the electrical decision and not a mechanical afterthought.

Where a family has run in the field for twenty years, the second source question is really a question about the reset timing. A replacement that asserts reset at a different threshold, or with a different delay, will pass a bench test and fail a production burn in, because the processor boots a fraction of a millisecond earlier than the flash is ready. The how to verify a drop-in replacement page sets out the four measurements that catch this class of difference before a build is released, and the power management cross reference page lists the parts in the same body with the same reset behaviour.

Questions buyers ask before ordering

Is the reset delay adjustable? No. The 200 millisecond delay is internal to the die, so the only choice is which family member is ordered, not how the delay is set.

Does the reset output need a pull up? Yes. It is open drain, so it sinks current and needs a resistor to the logic rail, typically 10 to 100 kiloohm depending on the leakage of the devices it holds.

Can it supply 500 mA continuously in the SOIC body? At 1.5 V out from 3.3 V the dissipation is 900 mW at full load. That is inside the package rating with a copper area, and outside it on a narrow trace, so the copper is part of the specification.

Ordering this part through SUPERB

SUPERB supplies this regulator against a bill of materials line, confirms the reel against the addendum row, and keeps the date code with the certificate so a second build matches the first. A quantity and a target date are enough to start, and the reel size comes back with the quote so the stores booking is made against a known unit. Send the rail, the load and the input bus through the one stop BOM sourcing page and the answer comes back with the reel size and the moisture level.