TPS76850QDR
Product Specifications
TPS76850QDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS76850QDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS76850QDR 1 A fixed 5 V regulator with power good in the SOIC body
The TPS76850QDR is the 5.0 V fixed member of the TPS768 family in the eight pin SOIC body, ordered on a reel. It carries 1 A from an input between 2.7 V and 10 V with 230 mV of typical dropout at full load, and it is stable with a 10 microfarad low ESR output capacitor rather than the larger tantalum the older parts in this class needed. The family is the one to reach for when a 5 V rail has to survive a fast load step, because the loop is compensated for a transient response rather than for the lowest quiescent current.
A power good output is included and it is open drain, so it needs a pull up and it can be wire ORed with the flag from another rail. Quiescent current is 85 microamp typical over the full load range, which is what the PMOS pass device buys: the gate current does not scale with load, so a rail that idles at low current still holds regulation. Output tolerance is 2 per cent over the specified conditions for the fixed versions, and thermal shutdown protects the die if the copper area is not enough for the dissipation.
Key parameters printed in the SLVS211L document
| Input range | 2.7 V to 10 V, with 5.0 V fixed output |
| Load current | 1 A continuous |
| Dropout | 230 mV typical at 1 A on the 5.0 V member |
| Accuracy | 2 per cent over the specified conditions for fixed output members |
| Quiescent current | 85 microamp typical across the full load range |
| Output capacitor | 10 microfarad low ESR, the value the loop is compensated for |
| Power good | Open drain output, needs an external pull up |
| Protection | Thermal shutdown, and a power on reset option in the TPS767 sibling with a 200 millisecond delay |
Package, reel and top side marking
| Package | SOIC, D body, eight pins |
| Reel | 2500 pieces on a large tape and reel for the DR row, 75 pieces in a tube for the plain D row |
| Finish and moisture | Nickel palladium gold, moisture level 1, unlimited floor life |
| Temperature and marking | Minus 40 to plus 125 degrees, top side marking 76850 |
Where a 1 A linear 5 V rail still wins
The usual application is a 5 V rail derived from a 9 V or 12 V adapter in an industrial box, where a switcher would add noise the sensors cannot take and the dissipation of 1 A across four volts is manageable in the SOIC body with a copper pour. It also suits a 5 V rail that has to be present before a processor boots, since the enable pin can be tied to the input through a divider and the power good flag then gates the processor reset. Where the same rail has to raise a reset rather than a flag, the sibling TPS767 part is the one to quote; the power management cross reference page lists both so a rail can be moved between the two without a new footprint.
One documentary point deserves attention before a purchase order. In the SLVS211L addendum the package, quantity and marking columns sit one line off from the order code column, so the row that reads TPS76850QDR prints a tube quantity and a level 1 finish that belong to the line above it. The DR row is a 2500 piece large reel; the plain D row is a 75 piece tube. A buyer who reads across the printed line rather than matching the code will order the wrong packaging, which is the kind of error that only shows up when the line is already waiting; the date code management page describes how SUPERB reconciles the reel label against the addendum row at goods in.
Questions buyers ask before ordering
Does the part need a minimum load? No. The pass device is a PMOS transistor driven by a voltage, so regulation holds down to no load and the quiescent current does not climb.
Can the power good pin drive a logic input directly? It is open drain, so it sinks current but does not source it. A 10 kiloohm pull up to the logic rail is the usual arrangement, and the pin can then be shared with another open drain flag.
What happens at thermal shutdown? The output turns off at 150 degrees junction and recovers when the die cools, so an undersized copper area shows up as a rail that cycles rather than as a dead part.
Ordering this part through SUPERB
SUPERB supplies this regulator against a bill of materials line and confirms the packaging on the reel label against the addendum row before shipping, because the difference between a tube and a reel is a line stop rather than a cost. Send the rail, the load and the input bus through the one stop BOM sourcing page and the answer comes back with the code, the reel size and the moisture level.