Contact Us

TPS74801RGWR

Brand: Texas Instruments
Texas Instruments TPS74801RGWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS74801RGWR — Power Management & Signal Chain | Superb Automation

TPS74801RGWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS74801RGWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS74801RGWR 1.5 A regulator with programmable soft start in the 20 pin VQFN

The TPS74801RGWR is the 1.5 A member of the TPS748 family in the 20 pin VQFN body, ordered on a 3000 piece reel. Output is adjustable from 0.8 V to 3.6 V, the main input covers 0.8 V to 5.5 V, and a bias rail of 2.7 V to 5.5 V carries the reference and the gate drive. The family appears in two silicon generations in the same document, and the addendum prints both, so a buyer comparing quotations from two sources can be looking at two different accuracy figures for what reads as one part number.

On the current silicon the accuracy is 1 per cent over line, load and temperature and the dropout at 1.5 A is 50 mV typical with a 100 mV maximum. The legacy silicon is quoted at 2 per cent and 60 mV typical with a 165 mV maximum. The current limit band is wide, 2 A to 5.5 A, which is deliberate on a 1.5 A part: it has to ride through the surge of a large ceramic bank without folding back before the rail is up. Soft start is set by a capacitor on the SS pin, and the ramp stays monotonic so a processor does not see a step in the middle of its own boot.

Key parameters printed in the SBVS074N document

Input range0.8 V to 5.5 V, floor also set by output plus dropout
Bias rail2.7 V to 5.5 V, 1 mA typical and 1.2 mA maximum of bias current
Output range0.8 V to 3.6 V adjustable from a 0.8 V reference
Load current1.5 A continuous, output current limit 2 A to 5.5 A
Accuracy1 per cent on the current silicon, 2 per cent on the legacy silicon, over line, load and temperature
Dropout50 mV typical and 100 mV maximum at 1.5 A on the current silicon, 60 mV and 165 mV on the legacy silicon
Rejection60 dB at 1 kHz and 50 dB at 300 kHz at 1.5 A on the current silicon
Noise and startup20 microvolt RMS over 100 Hz to 100 kHz with a 1 nF soft start capacitor; minimum start time 200 microseconds

Package, reel and top side marking

PackageVQFN, RGW body, 20 pins, exposed thermal pad
Reel3000 pieces on a large tape and reel
Finish and moistureNickel palladium gold, moisture level 2, one year floor life
Temperature and markingMinus 40 to plus 125 degrees junction, top side marking TPS 74801

Where a 1.5 A linear rail still makes sense

A 1.5 A linear rail is chosen when the switching stage upstream already exists and the last few hundred millivolts have to be clean. The arithmetic that decides the body is dissipation: 1.5 A from 2.5 V to 1.2 V is 1.95 W, which the 20 pin VQFN can hold with a proper thermal pad and a four layer board, and which a smaller body cannot. The second decision is the bias source, because the bias dropout of 1.31 V means a 3.3 V bias can only support an output up to about 2 V, and anything higher needs a 5 V bias. Suppliers who quote this family should be able to say which silicon generation the reel carries; the pin to pin cross reference page covers the bodies that share the footprint so a second source does not need a new land pattern.

Long life programs tend to standardise on one member and stay there for a decade, which is why the reel size and the moisture level matter as much as the electrical table. A level 2 part with a one year floor life needs dry storage discipline that a level 1 part does not, and a line that ignores it will see popcorning at reflow rather than a parametric failure. The component obsolescence management page sets out how the last time buy quantity is calculated when a family row moves to not recommended for new builds.

Questions buyers ask before ordering

Which silicon generation will I receive? Both are Active in the addendum, so the answer depends on the reel. Ask for the generation on the label, or accept the 2 per cent figure in the drawing, which covers both.

Can the output be set above 3.6 V? No. The maximum is 3.6 V on this family. A 5 V rail from a 5.5 V input is a different part and a different dropout budget.

Is the PG output push pull or open drain? Open drain on this member. It needs a pull up to the logic rail it drives, and it can be wire ORed with another supply in the same sequence.

Ordering this part through SUPERB

SUPERB quotes this part from a bill of materials line or a single call, confirms the body and the reel quantity against the addendum row, and ships with the certificate that carries the date code. Send the rail voltage, the load and the input bus and the answer comes back with the reel size and the moisture level; the power management cross reference page is the place to start when the line has to be filled from a second body.