TPS74701QDRCRQ1
Product Specifications
TPS74701QDRCRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS74701QDRCRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS74701QDRCRQ1 automotive 500 mA regulator with programmable soft start
The TPS74701QDRCRQ1 is the automotive half amp member of the TPS747 family in the ten pin VSON body, ordered on a 3000 piece reel. Output is set by two external resistors anywhere from 0.8 V to 3.6 V, the main input runs from 0.8 V to 5.5 V, and a separate bias rail from 2.7 V to 5.5 V feeds the internal reference and the gate drive. Splitting the two supplies is what lets the part hold a low dropout figure while the main input sits only a few hundred millivolts above the output, which is the case on a 1.2 V processor rail fed from a 1.5 V intermediate bus.
The AEC-Q100 record is grade 1, minus 40 to plus 125 degrees ambient, and the die is specified over the same window rather than a narrower commercial band. A capacitor on the SS pin sets the ramp, so the inrush into a large ceramic bank is stretched instead of switched, and the ramp is monotonic from the first millivolt. The PG output is open drain and can hold the next regulator off until this rail is inside tolerance, which removes the need for an external supervisor on a two rail sequence.
Key parameters printed in the SBVS141D document
| Input range | 0.8 V to 5.5 V, with the useful floor also set by output plus dropout |
| Bias rail | 2.7 V to 5.5 V, about 1 mA of bias current at 500 mA of load |
| Output range | 0.8 V to 3.6 V adjustable from a 0.8 V reference |
| Load current | 500 mA continuous, output current limit 800 mA to 1350 mA |
| Accuracy | 0.95 per cent over line, load and temperature |
| Dropout | 20 mV typical at 500 mA with the bias at 5 V; bias dropout 1.31 V typical and 1.39 V maximum |
| Rejection | 60 dB at 1 kHz with 1.8 V in and 1.5 V out at 500 mA |
| Noise and startup | 20 microvolt RMS on the current silicon over 100 Hz to 100 kHz with a 1 nF soft start capacitor; minimum start time 250 microseconds |
Package, reel and top side marking
| Package | VSON, DRC body, ten pins, 3 mm by 3 mm footprint |
| Reel | 3000 pieces on a large tape and reel |
| Finish and moisture | Nickel palladium gold, moisture level 1, unlimited floor life |
| Temperature and marking | Minus 40 to plus 125 degrees ambient, top side marking PAE |
Where this rail fits
The rail this part suits is a processor or FPGA core that has to come up after the input supply is stable, not at the same instant. Holding the enable pin low while the bias is alive keeps the pass device off with a shutdown current of about 1 microamp, and the soft start then decides how fast the ceramic bank charges. Thermal check is the second step: 500 mA from 3.3 V to 1.2 V is just over 1 W in the DRC body, so a two by two thermal via array under the pad and a copper pour on the top layer are part of the decision, not an afterthought. Buyers who need the same die in the SOIC style body are looking at a different family member, and the power management cross reference page lists the bodies that share the pin out.
Where supply is the pressing issue rather than the electrical choice, the practical question is which reel is in the channel this quarter. The automotive grade rows move on a different schedule from the catalog rows, and a line that stops because a Q1 reel is on allocation costs more than the part. The component lead time solutions page sets out how a scheduled call off works when the reel has to arrive in step with the build rather than in one drop.
Questions buyers ask before ordering
Is the bias rail mandatory? Yes. The main input alone cannot drive the pass device at low input, so the bias has to be present before the enable is released. A 5 V housekeeping rail is the usual source, and 2.7 V is the floor.
What sets the output voltage? Two resistors from OUT to the feedback pin and from that pin to ground, using the 0.8 V reference. The tolerance of those two parts adds directly to the 0.95 per cent device figure.
Does it work with a ceramic output capacitor? Yes. The document specifies stability with any capacitor of 2.2 microfarad or more, so a 4.7 microfarad X7R is comfortable and a 2.2 microfarad is the floor.
Ordering this part through SUPERB
SUPERB supplies this part against a bill of materials or a single line call, reads the reel label and the certificate back against the order, and holds the date code on record so a second build matches the first. A quantity, a target date and the rail it feeds are enough to start; send the list through the date code management page and the answer comes back with the reel size and the moisture level on the same line as the code.