TPS74701DRCR
Product Specifications
TPS74701DRCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS74701DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS74701DRCR 500 mA regulator with programmable soft start
The TPS74701DRCR is a 500 mA low dropout regulator in the ten pin VSON body that measures 3 mm by 3 mm, on a 3000 piece reel, with a programmable soft start and a power good output. The main input runs from 0.8 V to 5.5 V, the bias input from 2.7 V to 5.5 V, and the output is adjustable from 0.8 V to 3.6 V from a 0.8 V reference. It is the smaller sibling of the TPS742 and it shares the pin arrangement and the body size with the TPS748, which the document states as a compatibility note.
The reason this part exists next to the 1.5 A member is board space. A 500 mA rail on a line card does not need the twenty pin body, and the ten pin body gives the soft start and the power good in a land pattern that fits beside a connector. The price of that is 120 mV of dropout at full load instead of 100 mV, and a lower current limit.
Key parameters from the SBVS099H document
| Main input | 0.8 V to 5.5 V, with the floor set by output plus dropout |
| Bias input | 2.7 V to 5.5 V, which is what allows the main input below 2 V |
| Output range | 0.8 V to 3.6 V adjustable from a 0.8 V reference |
| Current | 500 mA continuous, current limit 1350 mA |
| Accuracy | 2 percent over line, load and temperature on this row, 0.95 percent maximum on the M3 suffix rows |
| Dropout on the main input | 50 mV typical and 120 mV maximum at 500 mA with the bias at least 3.25 V above the output |
| Dropout on the bias input | 1.31 V typical and 1.39 V maximum at 500 mA with the main input tied to bias |
| Bias current | 1 mA typical and 2 mA maximum at full load |
| Soft start | Charging current 440 nA on this row, minimum start up time 200 microseconds with the capacitor pin open |
| Power good | Trips at 85 to 90 percent of the output with 3 percent of hysteresis |
| Rejection | 60 dB at 1 kHz and 30 dB at 300 kHz from the main input, 50 dB and 30 dB from the bias |
| Order code | TPS74701DRCR, VSON ten pin 3 mm by 3 mm, 3000 pieces on a large reel, nickel palladium gold finish, level 2, one year floor life, marking CEG |
The M3 suffix is a different electrical table
The document carries two electrical tables, one for the orderable rows without the M3 suffix and one for the rows with it. The plain row has 2 percent accuracy over temperature and a 120 mV maximum dropout at 500 mA. The M3 row has 0.95 percent accuracy, a tighter line and load regulation, a fixed 800 mV dropout condition in its test setup and a different soft start charging current of 530 nA against 440 nA. The minimum start up time moves from 200 to 250 microseconds.
The catalogue entry here is the plain row, so the 2 percent figure applies. A customer who needs the tighter accuracy should be quoted the M3 code, and a customer who receives M3 parts against a plain order will find the start up ramp slightly slower than a board characterised on the plain row. The difference is small and the accuracy difference is not, which is the reason the two tables exist.
What the 50 mV dropout depends on
The 50 mV typical figure is quoted with the bias input at least 3.25 V above the output, and that condition is not decoration. The pass device is NMOS and needs a gate voltage above the output, which the bias rail supplies. A board that ties the bias pin to a 3.3 V rail and sets the output to 2.5 V has only 0.8 V of bias to output difference, and the dropout on the main input then rises toward the bias dropout figure rather than the 50 mV headline.
The bias dropout itself is 1.31 V typical and 1.39 V maximum, so the bias rail has to sit above the output by that much at full load. A 3.3 V bias supports an output up to about 1.9 V comfortably and up to 2.0 V at the limit. Above that the part still works and the dropout on the main input is no longer the published number. This is the single most common misunderstanding on this family, and it is worth stating to a customer before the board is laid out.
Where this part fits
Network attached storage, rack servers, network interface cards and merchant power supplies are the applications in the document, and the part turns up in our orders on line cards that need a 1.2 V or 1.8 V rail at a few hundred milliamps with a controlled start up. The cross reference notes are under power management cross reference, and the checks we run before accepting a substitute rail are in how to verify a drop in replacement.
Before a purchase order, and the questions that come up
Check the bias arrangement and the dissipation together. Dropping 3.3 V to 1.2 V at 500 mA burns 1.05 W in a ten pin body, which needs a ground plane and a reasonable ambient. The bias pin adds 1 mA of load on the rail that feeds it, which is a small item and one that is often missed in a budget with a 25 microamp class regulator elsewhere on the board.
Is the part a drop in for the TPS748? The document states the body and the pin arrangement are compatible, and the electrical differences are in that family's document. It is the substitution to check rather than assume.
What sets the soft start time? The capacitor from the soft start pin to ground and the 440 nA charging current. An open pin gives the 200 microsecond minimum, so a rail that must come up slowly needs a real capacitor rather than a short trace.
Does the power good output need a pull up? Yes, and it can be tied to the input rail or to the rail of the receiving device. The trip point is 85 to 90 percent of the output, so a rail that sags during a load step will release the signal again on the way back up, which is the behaviour a processor reset input wants.