Contact Us

TPS74533PQWDRBRQ1

Brand: Texas Instruments
Texas Instruments TPS74533PQWDRBRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS74533PQWDRBRQ1 — Power Management & Signal Chain | Superb Automation

TPS74533PQWDRBRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS74533PQWDRBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS74533PQWDRBRQ1 3.3 V automotive regulator in the eight pin VSON

The TPS74533PQWDRBRQ1 is the fixed 3.3 V member of the TPS745-Q1 family, in the eight pin VSON body with wettable flanks, on a 3000 piece reel. It is a 500 mA low dropout regulator with an open drain power good output, AEC-Q100 grade 1 qualified, and it is the member of the family that most automotive boards actually use, because 3.3 V is the rail that feeds the logic on almost every module.

The interesting number on this part is the dropout, 160 mV maximum at 500 mA, which is the lowest in the family because the pass device has the most headroom in this band. That makes it the natural choice for a rail fed from a 3.6 V to 4.2 V battery line during a cold crank, where a 200 mV difference decides whether the rail holds or collapses.

Key parameters from the SBVS355C document

Input range1.5 V to 6.0 V
Output3.3 V fixed, family covers 0.65 V to 5.0 V in 50 mV increments
Current500 mA continuous, current limit 515 to 865 mA with 720 mA typical
Short circuit current200 to 400 mA with 350 mA typical
AccuracyPlus or minus 0.85 percent at 25 degrees, plus or minus 1.5 percent maximum over temperature
Dropout160 mV maximum at 500 mA at 3.3 V out, the lowest band in the family
Quiescent current25 microamp typical, 1.5 microamp in shutdown
Rejection45 dB at 100 kHz
Output capacitor1 microfarad ceramic or larger
Thermal resistance55.5 degrees per watt junction to ambient in the eight pin VSON body
QualificationAEC-Q100 grade 1, minus 40 to 125 degrees ambient, junction to 150 degrees
Order codeTPS74533PQWDRBRQ1, 3000 pieces on a large reel, level 2, one year floor life

The dissipation is the whole story on a 3.3 V rail

A 3.3 V rail is usually fed from a 5 V bus or a battery line, and the drop across the regulator is the largest in the family. At 5 V in and 500 mA the part burns 0.85 W, which with the 55.5 degree per watt body is a 47 degree rise and a junction of 132 degrees at an 85 degree ambient. That is inside the rating and close enough to it that a sealed enclosure or a hot board should push the rail toward a switching regulator or a lower load.

At 250 mA the same rail burns 0.43 W and the rise falls to 24 degrees, which is comfortable. The pattern across this family is the same: the part is a good fit for a few hundred milliamps of post regulation and a poor fit for a full amp of continuous current from a high input. The electrical rating is 500 mA and the thermal answer is a different number.

Cold crank and the power good output

During a cold crank the battery line can fall to 3.0 V or lower, and a 3.3 V rail cannot hold with any regulator. What matters then is the behaviour on the way down and on the way back up. The undervoltage lockout holds the pass device off, the active discharge pulls the output down, and the power good output goes low, which is the signal a downstream processor should see. The part then comes back up with the soft start behaviour of the family when the input recovers, and the power good delay of 150 microseconds means the signal returns quickly.

A system that needs the rail to hold through the crank uses a boost converter in front, not a larger capacitor, because the capacitor energy at 500 mA is a few milliseconds and a crank is tens. The regulator's job in that architecture is to hold 3.3 V from the boosted rail, which it does with 160 mV of dropout and plenty of margin.

Where this part fits

Head units, cluster displays, cameras and telematics units all carry a 3.3 V rail, and it is the rail most often lost in a shortage because so many codes are similar. Our notes on the automotive grade route are under power management cross reference, and the rules we apply when a 3.3 V part has to be substituted on an existing board are in pin to pin cross reference.

Before a purchase order, and the questions that come up

Check the input and the load together. A 3.3 V rail at 500 mA from 5 V is 0.85 W and needs a copper area and a sane ambient. A 3.3 V rail at 500 mA from 12 V is 4.35 W and is not a linear regulator application at all, though customers ask for it. The document is clear about the thermal limits and the numbers are simple to run.

Is this a drop in for the 3.3 V member of another family? Mechanically it may be, electrically the accuracy and the power good behaviour differ, and the substitution should be checked against the load tolerance rather than the pinout alone.

Does the part need a feed forward capacitor? No, the fixed member has an internal divider and the transient curves are taken at one microfarad of output capacitance with no feed forward part.

What about reverse current? The active discharge handles a disabled rail, and a rail that is back fed from a live load should be checked against the absolute maximum on the output pin in the document.