TPS74513PQWDRBRQ1
Product Specifications
TPS74513PQWDRBRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS74513PQWDRBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS74513PQWDRBRQ1 1.3 V automotive regulator in the eight pin VSON
The TPS74513PQWDRBRQ1 is the fixed 1.3 V member of the TPS745-Q1 family in the same eight pin VSON body with wettable flanks, on a 3000 piece reel. It is a 500 mA low dropout regulator with a power good output, qualified to AEC-Q100 grade 1, and it decodes the same way as its 1.35 V sibling: 13 is the output at 1.3 V in two digits because the step is a round hundred millivolts, P is the active output discharge, the blank position after P is an open drain power good with a 150 microsecond delay, Q is the grade 1 marking and W is the wettable flank.
Fifty millivolts separates this part from the 1.35 V member, and that is worth understanding before treating them as interchangeable. The family is built in 50 mV steps and the two codes are two trim points on the same die, so the electrical table is shared and the difference is the internal divider. On a rail that feeds a memory device with a plus or minus 3 percent window, 50 mV is 3.8 percent of 1.3 V, which is outside the window on its own.
Key parameters from the SBVS355C document
| Input range | 1.5 V to 6.0 V |
| Output | 1.3 V fixed, family covers 0.65 V to 5.0 V in 50 mV increments |
| Current | 500 mA continuous, current limit 515 to 865 mA with 720 mA typical |
| Short circuit current | 200 to 400 mA with 350 mA typical, foldback behaviour |
| Accuracy | Plus or minus 0.85 percent at 25 degrees, plus or minus 1.5 percent maximum over minus 40 to 150 degrees junction |
| Dropout | 285 mV typical and 430 mV maximum at 500 mA in the 1.2 to 1.5 V band |
| Quiescent current | 25 microamp typical, 1.5 microamp in shutdown |
| Rejection | 45 dB at 100 kHz |
| Power good | Open drain with a 150 microsecond delay on this row, 5 ms delay and push pull variants exist under other letters |
| Thermal resistance | 55.5 degrees per watt junction to ambient, 20.8 degrees per watt junction to case top in the same body |
| Qualification | AEC-Q100 grade 1, minus 40 to 125 degrees ambient |
| Order code | TPS74513PQWDRBRQ1, 3000 pieces on a large reel, nickel palladium gold finish, level 2, one year floor life |
Where a 1.3 V rail actually comes from
The 1.3 V point is used on memory rails that are not the standard 1.2 V, on sensor cores and on some processor standby domains. It is also a common intermediate rail on boards that derive a lower core voltage from a higher one and want the intermediate to be regulated rather than divided. When a customer asks for a 1.3 V regulator the first question is whether the device tolerance is plus or minus 2 percent or plus or minus 5 percent, because the regulator accuracy of 1.5 percent over temperature leaves very little room against a 2 percent part in a worst case stack.
The second question is the input. A 1.3 V rail from a 3.3 V bus burns 1.0 W at 500 mA, and the eight pin body handles that with a 56 degree rise. From a 5 V bus the same rail burns 1.85 W and the rise is over 100 degrees, which puts the junction at the limit at a 40 degree ambient. Automotive boards that carry a 5 V bus usually put a switching regulator in front of a rail like this rather than dropping the whole difference in a linear part.
The power good delay is a system decision
The 150 microsecond delay on this row is fast. It is the right choice when the power good signal drives a reset supervisor that has its own delay, because the two delays add rather than fight. It is the wrong choice when the signal drives a processor enable directly and the rail has a large output capacitor, because a fast power good can assert before the output has actually reached its final value, and the processor starts while the rail is still climbing.
The family offers the 5 millisecond delay under the B letter and a push pull output under the C letter, and both are separate order codes. A customer who has a board that works with the fast output and wants to change to the slow one is changing the order code, not the board, which is worth saying early because the reel price and the lead time are the same.
Where this part fits
Camera modules, cluster displays, head units and short range radar modules use this family, and the 1.3 V point in our order book usually comes from a memory or sensor rail. The cross reference notes are under power management cross reference, and the rules we apply when a customer wants to move from a 1.35 V part to this one are in how to verify a drop in replacement.
Before a purchase order, and the questions that come up
Check the tolerance stack first. The regulator contributes 1.5 percent over temperature and the divider inside the part is trimmed, so the rest of the budget belongs to the load. A 1.3 V device with a 2 percent window gives 26 mV of total room, and a rail that is 50 mV off because someone substituted the 1.35 V code has already used twice that.
Is this a drop in for the 1.35 V member? Mechanically yes, electrically only if the load tolerates 1.35 V. The codes are two trim points on one die and the footprints are identical, which makes the substitution easy to make by mistake on a purchase order.
Does the part need a minimum output capacitor? One microfarad ceramic is the specification, and the transient curves are taken at that value. A board with 100 nF will usually run and will not meet the load step behaviour shown in the document.
What is the shutdown behaviour? The enable pin turns the pass device off and the active discharge pulls the output down, which is what keeps a rail from sitting up on a residual charge when the board is re sequenced.