Contact Us

TPS74501PDRVR

Brand: Texas Instruments
Texas Instruments TPS74501PDRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS74501PDRVR — Power Management & Signal Chain | Superb Automation

TPS74501PDRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS74501PDRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS74501PDRVR: 500 mA adjustable LDO with power good in a 6 pin WSON body

TPS74501PDRVR is a 500 mA adjustable regulator with a power good output and an active discharge, built for rails that have to sequence against a second supply in a WSON body of 6 pins. It takes 1.5 V to 6 V in, holds any output between 0.55 V and 5.5 V from a 1.5 V reference, and quotes 130 mV of maximum dropout at 500 mA on a 3.3 V rail. Accuracy is 0.7 per cent typical and 1 per cent maximum, quiescent current is 25 uA typical, and the power good pin trips at 94 per cent of the nominal output with a 165 us falling delay.

Order code and package

TPS74501PDRVR6 pin WSON (DRV), 3000 pieces on a large reel, marking 1MEH, moisture level 1 unlimited
TPS74501PDRVTsame body and silicon, 250 pieces on a small reel, the prototype quantity
TPS74501PDRVRG4same part with the green material declaration, 3000 pieces on a large reel
Feedback voltage1.5 V nominal on the feedback pin, so the divider sets any rail from 0.55 V upwards
Operating temperatureminus 40 C to plus 125 C junction across every row of the addendum

Electrical parameters that decide the application

Input voltage1.5 V to 6.0 V, with the enable pin rated to 10 V absolute
Output voltage0.55 V to 5.5 V adjustable
Output current500 mA maximum continuous
Dropout voltage130 mV maximum at 500 mA with a 3.3 V output, which is the figure the front page carries
Output accuracy0.7 per cent typical at 25 C and 1 per cent maximum over the full temperature range, excluding the divider
Quiescent current25 uA typical ground current with the output lightly loaded
Current limit585 mA to 865 mA foldback, so a shorted rail draws far less than the input voltage times 865 mA
Power goodtrips low at 94 per cent of nominal falling and releases at 92 per cent rising, 165 us of falling delay
Undervoltage lockout1.33 V maximum rising and 1.17 V minimum falling, with 40 mV of hysteresis
Soft startinternal ramp that brings the output up monotonically in about 500 us from the enable edge

The three functions that separate it from a plain LDO

Power good outputopen drain, needs a pull up between 10 kOhm and 100 kOhm to a supply that gives the receiving device a valid logic level
Active output dischargethe output is pulled down when the enable pin goes low, so a re enable starts from zero rather than from a stored charge
Monotonic startthe internal ramp is built to avoid the output dipping on the way up, which matters for a rail feeding a processor that latches its own supply state
Feed forward capacitorchanges the start up time constant and the loop response, so a rail that uses one needs the start up re measured
Foldback limitprotects the pass transistor during a short without a fuse
Six pin bodyinput, output, enable, feedback, power good and ground, with nothing left to configure

Points to check before this part goes on a BOM

The power good thresholds are 94 per cent falling and 92 per cent rising, which means a 1.2 V rail is flagged bad at 1.128 V and flagged good again at 1.104 V. That is a wide window with 165 us of delay on the falling edge, and it is deliberate: a supervisor that trips at 99 per cent chatters on any load step, while one that trips at 94 per cent reports a supply that has genuinely collapsed. A processor held in reset by this pin sees roughly 70 mV of hysteresis on a 1.2 V rail.

The 1.5 V reference is high for a modern LDO and it changes the divider arithmetic. A 0.55 V output from a 1.5 V reference runs the divider with the upper resistor below the lower one, which is unusual and makes the leakage of the feedback pin a larger share of the divider current. The vendor application section gives the resistor ranges, and copying a divider from a 0.6 V reference part produces a rail that is 25 per cent high.

Dropout at 130 mV maximum for 500 mA is not the lowest in the family of 500 mA parts, and the number belongs to a 3.3 V output. At 0.55 V out the pass element has far less headroom above the reference, and the dropout row in the table splits by output voltage for exactly that reason. A 1.0 V rail running from a 1.2 V supply has 200 mV to work with, which is inside the maximum and outside the typical.

The foldback current limit spans 585 mA to 865 mA, which is a wide window for a 500 mA part. A shorted rail on a 6 V input therefore dissipates between 3.5 W and 5 W in the pass transistor until the thermal shutdown takes over at 170 C. The part survives, but a small board with no copper under it will heat up first and a repeated short is a life test rather than a fault clearance.

The active discharge is the reason this part pairs well with a load switch. When the enable pin drops, the output falls through an internal path rather than waiting for the load to bleed it. That guarantees the next start is monotonic and that a rail which is re enabled 1 ms later does not begin from a partially charged output, a condition that produces a visible glitch on the downstream supply.

The ground current of 25 uA typical is respectable for a 500 mA part and it is quoted at light load. At full load the ground current rises with the gate drive of the pass element, so a battery rail that spends most of its life at 500 mA sees more than the headline. The vendor curve shows the shape, and it is a shallow rise rather than a step.

The feed forward capacitor is worth a separate note because it breaks the start up promise. With a capacitor across the upper divider resistor the loop responds faster but the ramp slows, and the monotonic behaviour is only guaranteed for the internal ramp. A rail that adds the capacitor and then fails a start up test is not a defective part, it is a changed circuit.

Where this order code fits

It supplies processor cores, FPGA auxiliary rails, sensor analogue supplies and radio baseband rails in products where a second rail has to come up in the right order and the power good signal is what enforces that order. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Kitting Service page.

Questions buyers ask

At what output voltage does the power good pin trip? At 94 per cent of nominal on the way down and 92 per cent on the way up, with a 165 us falling delay. The thresholds are percentages of the regulated output, so they scale with the divider.

Is 500 mA available with a 1.8 V output from a 2.5 V input? Yes, comfortably. The dropout at 500 mA and 1.8 V out leaves 700 mV of headroom, and the part runs in regulation with the pass element well inside its window.

What pull up does the power good output need? Between 10 kOhm and 100 kOhm to a supply that gives a valid logic level to whatever reads the pin. The pin is open drain and sinks 1 mA at 94 per cent of output, so the resistor value sets the rise time.

Why does the output go to zero when the enable pin drops? Because of the active discharge. It is built in rather than relying on the load to bleed the rail, which keeps the next start up monotonic.

What is the accuracy with 1 per cent resistors? The 1 per cent figure excludes the divider, so a 1 per cent part with 1 per cent resistors is roughly a 2 per cent rail. Use 0.1 per cent resistors when the rail is a reference.

Can it be used below 0.55 V out? No. The feedback reference sets the floor at 0.55 V, and going lower needs a part with a lower reference rather than a different divider.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.