Contact Us

TPS73701DCQRG4

Brand: Texas Instruments
Texas Instruments TPS73701DCQRG4 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73701DCQRG4 — Power Management & Signal Chain | Superb Automation

TPS73701DCQRG4

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73701DCQRG4 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73701DCQRG4 adjustable 1 A regulator in the SOT-223 body

The TPS73701DCQRG4 is the adjustable member of the TPS737 family in the six pin SOT-223 body, ordered on a 2500 piece reel with the G4 suffix. It is a 1 A low dropout regulator that runs from 2.2 V to 5.5 V, sets its output from 1.20 V to 5.5 V with two external resistors, and needs no more than one microfarad of ceramic on the output to stay stable. The pass device is an NMOS transistor in a voltage follower configuration, which is the reason the part tolerates almost any output capacitor value and equivalent series resistance while still holding a low dropout figure.

The G4 suffix is not a silicon change. It marks the green material row of the same die, and on this body the addendum prints a different lead finish for it: the plain TPS73701DCQR row carries a nickel palladium gold finish while the G4 row carries tin. Both rows sit at moisture level 2 with a one year floor life and both are listed Active in the addendum dated August 2025. A buyer who has a finish requirement written into the drawing should name the row, not the family.

Key parameters from the SBVS067W document

Input range2.2 V to 5.5 V, with the operating floor also set by output plus dropout
Output range1.20 V to 5.5 V adjustable from a 1.204 V reference, fixed members from 1.2 V upward
Current1 A continuous, foldback current limit, short circuit current 450 mA on the legacy chip and 510 mA on the current one
Initial accuracy1 percent at 25 degrees
Overall accuracy3 percent on the legacy silicon, 1.5 percent on the current silicon, over line, load and temperature
Dropout130 mV typical at 1 A on the legacy silicon, 122 mV typical on the current silicon
Quiescent current400 microamp at 10 mA of load, 880 to 1300 microamp at full load depending on chip generation
Shutdown currentUnder 20 nA typical with the enable held low
Rejection58 dB at 100 Hz and 37 dB at 10 kHz at 1 A of load
Noise27 microvolt RMS over 10 Hz to 100 kHz at 3 V out, reduced further with a capacitor on the NR pin
Thermal resistance53.1 degrees per watt junction to ambient in the DCQ body on a JEDEC board
Order codeTPS73701DCQRG4, SOT-223 six pin, 2500 pieces on a large reel, tin finish, level 2, one year floor life

Two silicon generations under one order code

The current document splits its electrical table into rows marked legacy silicon and new silicon. The difference that shows up on a bench is the overall accuracy, 3 percent on the legacy chip against 1.5 percent on the current one, and the dropout, 130 mV against 122 mV at the same 1 A. The quiescent current at full load also moves, from 1300 microamp to 880 microamp, and the short circuit current moves from 450 mA to 510 mA. None of that is visible on the reel label and the order code does not change, so a board that was signed off on samples from one lot can measure slightly different numbers on a production lot.

Where the rail is a post regulator behind a switching supply and the load is a processor core, the accuracy difference is the one that matters, because 3 percent of 1.2 V is 36 mV of window that the processor tolerance has to absorb. Where the rail feeds an analog block with its own reference, the dropout and the noise figure are the ones to watch. The practical rule at receipt is to measure the output at the actual load and the actual input rather than trusting the typical column, and to keep the lot number with the measurement.

Where the reverse current protection earns its place

The NMOS follower blocks reverse current when the device is disabled, and the document states that no bias voltage is needed on any pin for that blocking to work. On the adjustable member there is one exception worth writing down: reverse current can flow when the feedback pin sits more than 1.0 V above the input. That happens on a board where the output rail is held up by a large bulk capacitor or by a second supply while the input collapses, and the divider from output to feedback carries the output voltage onto that pin. A rail that is back fed in test or in a dual supply arrangement should be checked against that 1.0 V figure rather than assumed safe.

The second case is the enable pin tied to the input. The document allows that connection when shutdown is not used, but warns that the pass transistor can stay on for a significant time after the input is removed, which turns the output capacitor into a source that pushes current back through the regulator. Where a board relies on the input being switched off, the enable should be driven from the same rail through a resistor divider so the part turns off with the rail.

Where this part fits

Point of load regulation for DSPs, FPGAs, ASICs and microprocessors is the first application in the document, and post regulation behind a switching supply is the second. In our order book the SOT-223 body turns up on industrial controllers, telecom line cards and older medical boards where the tab is soldered to a copper area and the assembly is mixed through hole and surface mount. The cross reference data we keep for this family sits under power management cross reference, and the checks we run when a rail has to change part are in how to verify a drop in replacement.

Before a purchase order, and the questions that come up

The thermal case decides the input voltage. Dropping 5 V to 1.2 V at 1 A burns 3.8 W in a body whose junction to ambient resistance is 53 degrees per watt, which is a 200 degree rise before the ambient is counted. The part cannot run that operating point, and no copper area rescues it. The same load from a 2.5 V input burns 1.3 W and gives a 69 degree rise, which is workable on a board with a decent ground plane. A customer asking for 1 A at 1.2 V from a 5 V bus is asking for a switching regulator followed by this part, not for this part alone.

Does the adjustable member need a capacitor on the NR pin? It helps noise and it is optional. The pin is shared between noise reduction and feedback depending on the member, so on the adjustable part it is the feedback node and the capacitor goes from output to that node, not to ground.

Can a fixed member be replaced by the adjustable one set to the same voltage? Yes electrically, and the footprint is the same in the DCQ body, so the board needs the divider added and the feedback pin connected. It is a small change, not a drop in without a board revision.

Does the part need a minimum load? No. The document specifies regulation from 1 mA, and the dropout curves are taken down to 10 mA, so a rail that sleeps at a few hundred microamp still regulates.