Contact Us

TPS73525DRVR

Brand: Texas Instruments
Texas Instruments TPS73525DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73525DRVR — Power Management & Signal Chain | Superb Automation

TPS73525DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73525DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73525DRVR 2.5 V rail in the six pin WSON

The TPS73525DRVR is the 2.5 V fixed member of the TPS735 family in the six pin two millimetre WSON, a 500 mA regulator with 45 microamp of ground current that runs from 2.7 V to 6.5 V. It is the small body version of the 2.5 V point, and its place in a bill of materials is decided by area rather than by current: the same die in the eight pin SON costs one square millimetre more and buys a lower junction to ambient resistance.

At 2.5 V out the dropout specification does apply, unlike the 1.2 V member, because the output is above the 2.8 V threshold the vendor uses for the measurement. That means a 3.3 V bus leaves 800 mV of headroom against a 500 mV maximum dropout at full load, which is a real margin at temperature rather than a bench coincidence.

Key parameters from the SBVS087M document

Input range2.7 V to 6.5 V
Output2.5 V fixed, factory trimmed
Current500 mA continuous
Accuracy2 percent over load, line and temperature, 3 percent allowance below 2.2 V output
Dropout280 mV typical, 500 mV maximum at 500 mA
Ground current45 microamp typical, 65 microamp maximum
Shutdown current0.15 microamp typical, 1 microamp maximum
Rejection66 dB at 100 Hz, 68 dB at 1 kHz, 44 dB at 10 kHz, 22 dB at 100 kHz
Noise11 microvolt RMS with 10 nanofarad on the noise reduction pin
Lockout1.9 V to 2.65 V rising, 70 mV of hysteresis
PackageDRV six pin WSON, 2 mm by 2 mm, marking NSW
Order codeTPS73525DRVR active, 3000 pieces on a large reel, level 1 with unlimited floor life

2.5 V from 3.3 V is the comfortable case

Dropping 3.3 V to 2.5 V at 500 mA burns 0.4 W. In the six pin body on a high-K board the junction to ambient resistance is roughly 60 degrees per watt, so the rise is about 24 degrees and the part has room even in a 60 degree cabinet. That is the operating point this member is usually bought for, and it is the reason a 2.5 V rail on a 3.3 V bus is one of the few linear regulator cases that survives a full load check.

From a 5 V bus the same rail burns 1.25 W and the rise triples, so a 5 V to 2.5 V conversion at 500 mA belongs in a switching converter with this part used as a post regulator, or in a lower current branch. The part does not hide that: the dropout and the thermal numbers are published, and the arithmetic is two multiplications.

Where this part fits

Industrial sensors, motor control boards, telecom line cards and handheld instruments use a 2.5 V rail for analog front ends and memory. Our substitution notes for the 2.5 V point are under power management cross reference, and the way we stage parts for a build so a rail is not held up by one line item is in kitting service.

What to check before a purchase order

Check the body against the copper. The six pin WSON has an exposed pad and the thermal numbers assume it is soldered to a copper area with vias. A footprint that treats the pad as a mechanical feature rather than a heat path loses most of the advantage over a five pin SOT-23 and the part derates to a few hundred milliwatts.

Check the level 1 claim on the label. This row is published at level 1 with unlimited floor life, which is a handling convenience over the automotive member of the family. Where a distributor offers the automotive row as a substitute, the floor life drops to 168 hours and the line planning changes.

Questions that come up on this part

Can the noise reduction pin be tied to ground? No. The pin expects a capacitor to ground; a direct short removes the bypass without removing the noise, and the vendor does not specify the part in that state.

Does the regulator need a minimum output capacitor? The family is specified with 2.2 microfarad, and the transient curves are taken with that value. A 1 microfarad part will usually work and is outside the published condition, which matters on a board that is being qualified rather than prototyped.

How much copper does the six pin body need? The thermal numbers in the document are quoted for a JEDEC high-K board with a copper area under the pad, and the value falls quickly with a smaller area. On a two layer board with a modest pad, treat the usable dissipation as roughly half the table value and check the junction temperature at the highest ambient the product will see.