Contact Us

TPS73512DRBR

Brand: Texas Instruments
Texas Instruments TPS73512DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73512DRBR — Power Management & Signal Chain | Superb Automation

TPS73512DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73512DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73512DRBR 1.2 V fixed rail from a 500 mA regulator

The TPS73512DRBR is the 1.2 V fixed member of the TPS735 family, a 500 mA regulator in the eight pin three millimetre SON, running from 2.7 V to 6.5 V with 45 microamp of ground current. It is the version to use when a 1.2 V core rail has to come from a 3.3 V or 5 V bus and the board wants a regulator with a real thermal pad rather than a five pin body.

This is also the member of the family where the data sheet carries a warning that a buyer rarely reads. The dropout voltage is not measured for outputs below 2.8 V, because the minimum input of 2.7 V is already close to the output plus dropout, and the footnote says so explicitly. A specification table that shows no dropout figure for the 1.2 V part is not an omission, it is the vendor saying the 1.2 V rail is characterised by its input range instead.

Key parameters from the SBVS087M document

Input range2.7 V to 6.5 V, which is the number that governs this member
Output1.2 V fixed, factory trimmed
Current500 mA continuous
Accuracy2 percent over load, line and temperature, with a 3 percent allowance below 2.2 V
Dropout280 mV typical and 500 mV maximum at 500 mA, not specified for outputs below 2.8 V
Ground current45 microamp typical, 65 microamp maximum
Shutdown current0.15 microamp typical, 1 microamp maximum
Rejection68 dB at 1 kHz, 44 dB at 10 kHz, 22 dB at 100 kHz
Noise11 microvolt RMS with 10 nanofarad on the noise reduction pin
PackageDRB eight pin SON, 3 mm by 3 mm, marking QTT
Moisture levelLevel 1 at 260 degrees with unlimited floor life, tin plating
Order codeTPS73512DRBR active, 3000 pieces on a large reel

The 1.5 V of headroom is the whole story

From a 2.7 V input a 1.2 V output at 500 mA burns 0.75 W in the regulator. The eight pin SON on a high-K board is about 50 degrees per watt junction to ambient, so that is a 37 degree rise, which is manageable. From a 3.3 V input the same load burns 1.05 W and the rise goes to about 52 degrees, which still fits under a 125 degree junction in a 40 degree cabinet, but leaves nothing for a second heat source nearby. From 5 V the dissipation is 1.9 W and the part needs a copper area far beyond what the three millimetre body suggests.

The arithmetic is the reason a 1.2 V core rail is usually made with a switching converter and this part is used for the analog or standby branch. Where the load is a few tens of milliamps rather than the full 500, the linear regulator is the cheaper and quieter answer, and the same part covers both because the ground current does not rise with load the way an older bipolar regulator does.

Where this part fits

FPGA and processor boards that need a quiet 1.2 V analog branch, instrumentation with a 1.2 V reference rail, and telecom cards that carry a low voltage logic supply from a 3.3 V backplane all use this member. Our notes on supplying the same rail from a different family are under pin to pin cross reference, and the questions we ask before a board is re-qualified around a new regulator are in how to verify a drop in replacement.

What to check before a purchase order

Check that the input really stays above 2.7 V. The part has an undervoltage lockout that begins to release at 1.9 V and is guaranteed by 2.65 V, so an input that sags to 2.6 V under load will hold the output on a threshold that is not specified. A 1.2 V rail on a 5 V bus is fine; a 1.2 V rail on a two cell pack that ends at 2.4 V is not.

Check the noise reduction pin. On this member the difference between 11 microvolt and 95 microvolt RMS is the difference between a rail that can feed a converter reference and one that cannot, and the capacitor is 10 nanofarad in an 0402 case, so there is no reason to omit it on a new board.

Questions that come up on this part

Why is there no dropout row for this voltage? Because the family is specified from a 2.7 V input, and the vendor states that dropout is not measured below 2.8 V of output as the input floor would be violated. The input range is the specification for this member.

Can this part be used as a 1.2 V termination rail for a memory bus? It can, and the transient response is adequate for that load, but a termination rail usually needs to sink current as well as source it, which this regulator does not do. A dedicated termination regulator is the correct part there.