TPS73218DCQR
Product Specifications
TPS73218DCQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS73218DCQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS73218DCQR 1.8 V regulator in the SOT-223 body
The TPS73218DCQR is the 1.8 V fixed member of the TPS732 family, a 250 mA regulator with the same capacitor free topology as the TPS731 but a higher current rating and a larger pass device. It runs from 1.7 V to 5.5 V, holds 0.5 percent initial accuracy and takes no output capacitor for stability. The DCQ suffix is the six pin SOT-223, which is the body to pick when the board is a through hole mixed assembly or when the thermal path matters more than the footprint, because the tab of a SOT-223 solders to a copper area in a way a five pin SOT-23 cannot match.
At 1.8 V out and 250 mA the electrical case is comfortable: dropout is 40 mV typical and 150 mV maximum, so a 2.5 V input is enough over temperature, and the part dissipates 0.175 W at that input against 0.9 W if the input were 5.5 V. The second number is the one that decides the copper area, not the first.
Key parameters from the SBVS037S document
| Input range | 1.7 V to 5.5 V |
| Output | 1.8 V fixed, adjustable member uses a 1.204 V reference |
| Current | 250 mA continuous |
| Accuracy | 0.5 percent typical, 1 percent maximum over load, line and temperature |
| Dropout | 40 mV typical, 150 mV maximum at 250 mA |
| Quiescent current | 400 microamp typical, 550 microamp maximum on the legacy chip and 580 on the current chip |
| Current limit | 250 mA minimum, 600 mA maximum, 425 mA typical |
| Short circuit current | 300 mA at a shorted output |
| Shutdown current | 0.02 microamp typical, 1 microamp maximum |
| Rejection | Quoted at full load in the family table, 58 dB at 100 Hz |
| Package | DCQ six pin SOT-223, marking PS73218 |
| Order code status | The plain TPS73218DCQR row reads Obsolete in the addendum dated 11 April 2026, only the .A row is Active |
The order code is the risk on this one
The addendum prints two rows for the DCQ body. TPS73218DCQR carries the status Obsolete, and TPS73218DCQR.A carries Active, both at the same body, the same marking PS73218 and the same minus 40 to 125 degree range. The lead finish and moisture level columns on both rows read Call TI rather than a specified finish, which means the vendor has not published a floor life for this body. A buyer who sends this code to a distributor without the .A will receive a part the vendor lists as obsolete, and a substitute offered in its place will often be a different package.
Where the board is new, the honest answer is that the SOT-223 1.8 V point is a legacy format and the same rail is available in a five pin SOT-23 under a different family. Where the board is existing and the SOT-223 tab is part of the thermal path, the .A row is the row to order, and a last time buy is worth discussing because an obsolete row can stop without notice.
Where this part fits
Set top boxes, routers, industrial controllers and older medical boards use a 1.8 V rail from a 3.3 V or 5 V bus, and the SOT-223 body is common on boards of that generation. Our notes for parts that have gone obsolete while the board is still in production sit under last time buy and LTB planning, and the substitute checks we run before a rail is changed are in pin to pin cross reference.
What to check before a purchase order
Check the status of the exact row, not the family. A family page that shows the part in production is usually showing the newest revision of the string, and the status column of the row that matches the plain code is what the distributor honours. Ask for the addendum date as well, because the status of a legacy row can change between two addenda a quarter apart.
Check the thermal path of the tab. The SOT-223 tab is the only low resistance path out of the die, and a footprint that connects the tab to a thin trace rather than a copper area gives up most of the advantage of the body. At 5.5 V in and 1.8 V out the part burns 0.9 W at full load, which no SOT-223 survives without a copper area of a few square centimetres.
Questions that come up on this part
Can the fixed 1.8 V part be replaced by the adjustable member set to 1.8 V? Electrically yes, and the pinout of the DCQ body differs, so the board has to carry the divider and the feedback pin. It is a board change, not a drop in.
Does the part need any output capacitance for transient response? Not for stability, but the published load transient curves are taken with 0.1 microfarad fitted, and a board with a fast load step will show more undershoot without one. A small ceramic is cheap insurance even where it is not required.