Contact Us

TPS72301DDCR

Brand: Texas Instruments
Texas Instruments TPS72301DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS72301DDCR — Power Management & Signal Chain | Superb Automation

TPS72301DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS72301DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS72301DDCR: negative 200 mA low noise regulator with 60 uV of noise from a -10 V input

TPS72301DDCR is a small negative linear regulator for analog rails, adjustable from -1.186 V to -10 V with a 140 mV dropout at full current in a SOT-23 body of 5 pins. The TPS72301 is a negative low dropout regulator that takes -2.7 V to -10 V in, with an absolute maximum of -11 V, and delivers up to 200 mA. Its noise is 60 uV root mean square with a 10 nF noise reduction capacitor, ripple rejection is 65 dB at 1 kHz and 40 dB at 100 kHz, and dropout is 140 mV typical at 200 mA. The adjustable member covers -1.186 V to -10 V and the family also offers a fixed -2.5 V version. Accuracy is plus or minus 1.6 percent on the current chip and 3 percent on the older one.

Order code and package

Order codeTPS72301DDCR
Input voltage-2.7 V to -10 V, -11 V absolute maximum
Output current200 mA
Output voltage-1.186 V to -10 V, adjustable
Noise60 uV root mean square with a 10 nF noise reduction capacitor
Ripple rejection65 dB at 1 kHz, 40 dB at 100 kHz
Dropout140 mV typical at 200 mA on the current chip
Accuracyplus or minus 1.6 percent on the current chip
Quiescent current30 uA at zero load on the current chip
Output capacitor2.2 uF ceramic, stable
Package5 pin SOT-23
Fixed option-2.5 V in the same family
DocumentTPS723 family data sheet

Electrical parameters that decide the application

Dropout on the legacy chip280 mV typical at 200 mA
Accuracy on the legacy chipplus or minus 3 percent
Polaritynegative output, input more negative than the output
Noise reductiona capacitor on the NR pin, 10 nF for the published figure
Junction range-40 C to 125 C
Enablelogic level input
Thermal paththe five pin SOT-23 body on a copper pad
Protectioncurrent limit and thermal shutdown
Reference-1.186 V nominal
Load regulationspecified in the electrical table over the 0 to 200 mA range
Line regulationspecified over the full input range
Capacitorceramic 2.2 uF minimum, with the polarity correct for a negative rail

Points to check before this part goes on a BOM

Two chips exist under this part number, and the electrical table separates them. The current chip gives 140 mV of dropout and 1.6 percent accuracy, the legacy chip 280 mV and 3 percent. A board that was qualified on one and refilled with the other will work at a comfortable input but can lose regulation at the bottom of the range, which is exactly where a battery powered instrument spends its last hour.

Sixty microvolts of noise is measured with a 10 nF capacitor on the noise reduction pin, and the pin is not optional if the number matters. The same applies to the soft start, which the capacitor also sets. A board that needs the lowest noise should use the capacitor value in the electrical table and not a larger one chosen for a slower ramp.

Rejection of 40 dB at 100 kHz is modest, and it is the band where a small switching converter in front would sit. Two regulators in series, a switcher followed by this part, therefore rely on this part for the low frequency ripple and on the output capacitor for the high frequency. A ferrite bead between them shifts the crossover and is often worth the board space.

A 5 pin SOT-23 is a small thermal package. At 200 mA and a 3 V drop the dissipation is 600 mW, which the body can only carry with a copper pad and a reasonable ambient. In a -5 V rail from a -9 V input the drop is 4 V and the dissipation at full load is 800 mW, so the package is the limiting element rather than the current rating.

Negative regulators need the output capacitor connected with the correct polarity, and on a negative rail that means the positive terminal goes to ground. A board assembled with the capacitor the wrong way round will work briefly and then fail, and the failure looks like a regulator problem rather than an assembly problem. That is worth a marked footprint and a line in the inspection plan.

The enable pin is referenced to the input, not to ground, which is a detail that catches level shifting circuits. A control signal from a positive logic domain has to be translated to the negative rail, and a simple resistor divider from a positive supply will not do it. Boards that share an enable across a bipolar supply need a translator or an optocoupler.

Thirty microamps of quiescent current on the current chip is low for a negative regulator and it is what makes this part usable in a battery instrument that keeps its analog rail alive between measurements. The legacy chip draws more, so a standby current measurement is one way to tell which chip is on the board.

Where this order code fits

This order code fits a negative rail beside a positive analog supply in portable instruments, sensor interfaces and audio equipment running from a -5 V or -9 V rail. The 10 V input ceiling keeps it in the low voltage domain, which is where most bipolar analog front ends live. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

What is the difference between the two chips? Dropout 140 mV against 280 mV, accuracy 1.6 percent against 3 percent, and quiescent current 30 uA against a higher figure. The part number does not change.

Can it be used with a positive input? No. It is a negative regulator, and the input has to be more negative than the output by at least the dropout voltage.

How is the output set? By a divider from the -1.186 V reference for the adjustable member, or fixed at -2.5 V on the other member of the family.

SUPERB supplies this order code with date codes and packing on the offer, and the Obsolete RF Part Replacement page covers the checks for a negative rail that has to stay sourced after the vendor changes the die.