Contact Us

TPS72010DRVR

Brand: Texas Instruments
Texas Instruments TPS72010DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS72010DRVR — Power Management & Signal Chain | Superb Automation

TPS72010DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS72010DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS72010DRVR: 350 mA low dropout regulator with a bias pin, fixed 1.0 V output, in a 2 mm by 2 mm WSON

TPS72010DRVR is a linear regulator that runs from a supply only 500 mV above its output and takes its drive current from a separate bias rail in a WSON body of 6 pins. It holds a 1.0 V core rail from a 1.2 V or 1.5 V buck output, which is the case where an ordinary LDO has no headroom left to work with.

Order code and package

Order codeTPS72010DRVR, DRV package, WSON 2 mm by 2 mm, six pins with a thermal pad, 3000 pieces on a large reel
Body optionsDRV is the six pin WSON, YZU is a five pin die scale package, and the electrical limits differ between them
Fixed output1.0 V on this order code, with TPS72012 at 1.2 V, TPS72018 at 1.8 V and the TPS7201 adjustable
PinsIN, OUT, BIAS, EN, GND and the thermal pad, with no bypass pin on the fixed versions
Output capacitor2.2 uF ceramic, which is also the value the start-up and transient limits are specified at
ReferenceInternal, trimmed at wafer level, so there is no divider to add error to the output

Electrical parameters that decide the application

Input range1.1 V minimum on IN, up to 4.5 V, with the output set 500 mV below the input or lower
Bias rail2.5 V to 5.5 V on BIAS, which supplies the internal drive and does not carry the load current
Output current350 mA continuous, with the current limit above that and thermal shutdown behind it
Dropout110 mV at 350 mA, so a 1.0 V output needs at least 1.11 V on IN at full load
Quiescent current38 uA typical, which is what the bias rail pays when the load is light
Noise48 uV RMS from 10 Hz to 100 kHz, which is the figure to compare against a converter rather than an LDO
Rejection80 dB from IN and 70 dB from BIAS, both measured from 10 Hz to 10 kHz
Accuracy1 per cent on the DRV package over line, load and the full temperature range
Transients15 mV of output change for a 0 to 350 mA load step in 1 us, 2 mV for a 600 mV step on BIAS
Start-up140 us to reach regulation, with the output rise monotonic and overshoot limited to 3 per cent
InrushLimited to 100 mA plus the load current with a 2.2 uF output capacitor

Family variants and how they differ

TPS72012DRVRthe same die trimmed to 1.2 V, which is the other common core rail on the same board
TPS72018DRVRthe same die at 1.8 V, for a rail that has more headroom and more dissipation
TPS7201the adjustable member of the family, for a rail that has to be trimmed at test
TPS7A20a lower current LDO from a different family, for a rail that only needs tens of milliamps
A buck converterthe alternative when the drop across the regulator would exceed the thermal budget, at the cost of switching noise on the rail

Points to check before this part goes on a BOM

The bias pin is what makes a 1.0 V output possible from a 1.2 V input. The pass element needs gate drive above the input, and a conventional LDO would have to generate it with a charge pump from the same rail, which is noisy and inefficient at low headroom. Here the drive comes from BIAS at 2.5 V to 5.5 V, so IN only has to carry the load current and the dropout falls to 110 mV at 350 mA.

That bias rail is not free. It has to be present before the enable pin goes high, it has to stay above 2.5 V, and it carries the 38 uA of quiescent current plus the gate charge of the pass element. A board that powers BIAS from a rail that comes up late will see the output sit at zero while IN is healthy, which reads as a dead regulator and is usually a sequencing problem rather than a part failure.

The 110 mV dropout is specified at 350 mA, so the minimum input for a 1.0 V output at full load is 1.11 V. A 1.2 V buck output with two per cent tolerance is 1.176 V at the low end, which leaves 66 mV for the copper between the converter and the regulator and for the ripple on the 1.2 V rail. That is a thin budget, and it is the reason the regulator belongs close to the buck output with a short, wide trace rather than on the far side of the board.

The 1 per cent accuracy figure belongs to the DRV package over the full range. The YZU die scale package carries a narrower condition, from minus 10 C to 85 C, so a board that substitutes the smaller body for space gets a different accuracy promise as well as a different thermal path. The two are not interchangeable on a specification review even though both are 350 mA parts.

Noise of 48 uV RMS is the number that decides whether this regulator can feed a converter or a clock. On a 1.0 V rail a 12 bit converter has a 244 uV step, so 48 uV is a fifth of a step, and on a 16 bit converter it is 3 steps. Rejection is 80 dB from IN and 70 dB from BIAS, both measured only to 10 kHz, so a 2.4 MHz buck in front of it is attenuated by the output capacitor and the regulator loop rather than by the specified rejection.

The transient figures are the reason to choose this part over a smaller LDO. A 0 to 350 mA step in 1 us moves the output by 15 mV, which on a 1.0 V rail is 1.5 per cent, and the recovery is set by the loop rather than by the output capacitor alone. A 2.2 uF output is small enough that the loop has to be fast, and the data sheet's stability requirement is that the capacitor stays within its tolerance over temperature and bias.

Start-up is 140 us with a monotonic rise and 3 per cent overshoot, and the inrush is limited to 100 mA plus the load. That limit is what keeps a 2.2 uF output from pulling a spike out of the 1.2 V buck when the enable pin is released, which matters when the same rail feeds several regulators that are enabled together. The rise time is short enough that a sequencing scheme built on RC delays will not see it at all.

The thermal budget is the limit on this part at low output voltages. At 1.2 V in and 1.0 V out and 350 mA, the regulator dissipates 70 mW, which a 2 mm by 2 mm WSON sheds easily. Move the input to 3.3 V and the same load dissipates 805 mW, which the same body cannot hold without a copper plane. The part is specified for a low headroom application and the derating curve, not the 350 mA headline, is what decides whether it survives a 3.3 V rail.

Where this order code fits

It belongs behind a buck converter on a core rail: a 1.2 V or 1.5 V intermediate rail feeding a 1.0 V FPGA or DSP core, a serializer supply, or any load that needs the switching ripple removed without a second converter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the RF Component Sourcing page.

Questions buyers ask

Can it run from a 1.2 V input at 350 mA? Yes, but only just. Dropout is 110 mV at 350 mA, so 1.11 V is the floor and the 1.2 V rail has to hold its tolerance and the copper drop inside the remaining 66 mV.

What is the bias pin for? It supplies the internal gate drive, so the input only carries load current. Without a bias rail above 2.5 V the regulator does not start, regardless of the input voltage.

Is the adjustable version pin compatible? It is the same family and the same body options, but the adjustable part brings the feedback node out and needs a divider, so the BOM and the accuracy budget both change.

How much heat at 3.3 V in and 1.0 V out? About 805 mW at 350 mA, which is well beyond the 2 mm by 2 mm body without a copper plane. This part is intended for a low headroom rail, not a 3.3 V one.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.