Contact Us

TPS71530DCKR

Brand: Texas Instruments
Texas Instruments TPS71530DCKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS71530DCKR — Power Management & Signal Chain | Superb Automation

TPS71530DCKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS71530DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS71530DCKR: 3.0 V fixed, 50 mA, 24 V input, 3.2 microamp quiescent LDO, SC70-5

TPS71530DCKR is a fixed 3.0 V linear regulator that takes up to 24 V in, delivers 50 mA and draws 3.2 microamp of quiescent current, in a five pin body smaller than a grain of rice in a SC70-5 body of 5 pins. The input range is 2.5 V to 24 V, with 30 V allowed on the newer silicon, and the output is fixed at 3.0 V on this string. Dropout is 415 mV typical at 50 mA, and the quiescent current stays at 3.2 microamp across the whole load range, which is what makes the part usable on a battery that has to last years. Output accuracy is plus or minus 4 per cent over line, load and temperature.

Order code and package

TPS71530DCKRActive, SC70 (DCK) body, 5 pins, 3000 pieces on a large reel, marking AQM
TPS71530DCKR.AActive, same body and same 3000 piece reel, material row printed separately
TPS71530DCKRM3Active, the same part with a different reel and marking arrangement
TPS71501the adjustable member, 1.205 V reference, output up to 15 V, same body
Temperature rangeminus 40 to 125 degrees junction

Electrical parameters that decide the application

Input voltage2.5 V to 24 V, with 30 V maximum on the newer silicon
Output voltage3.0 V fixed on this string, 1.8 V to 5 V across the family
Output current50 mA maximum
Quiescent current3.2 microamp typical, 4.8 microamp maximum over the load range
Dropout415 mV typical at 50 mA
Output accuracyplus or minus 4 per cent over line, load and temperature
Line and load regulation20 to 22 mV over the full input range and load range
Output capacitorstable with 0.47 microfarad or larger

Family variants and how they differ

TPS715303.0 V fixed, the string on this page
TPS71533 and TPS715253.3 V and 2.5 V fixed members, same body and same current
TPS71501adjustable from a 1.205 V reference, for outputs outside the fixed list
TPS715Athe 80 mA member in a larger body, for a load that outgrows this one
Input ceilingthe older silicon stops at 24 V, the newer silicon is rated to 30 V

Points to check before this part goes on a BOM

Twenty four volts input and 3 microamp quiescent is an unusual pair. Most wide input regulators pay for the range with hundreds of microamp of quiescent current, and most micropower regulators cannot take more than 6 V. This part does both, which is why it appears in industrial sensor loops and battery instruments where a 24 V bus and a long sleep are both present.

The two silicon revisions have different input ceilings. The data sheet prints 24 V for the original chip and 30 V for the newer one, and the same orderable string can ship either. A board that runs a 28 V rail into this part is relying on the newer silicon without a way to tell which one arrived. The safe engineering answer is to keep the input at or below 24 V, or to ask for a date code range that guarantees the new chip.

Four per cent output accuracy is a sensor rail tolerance, not a reference. A 3.0 V rail at minus 4 per cent is 2.88 V, which is below what some 3.3 V logic accepts as a valid supply. The part is intended for a microcontroller that works down to 2.7 V, a sensor bridge or an analogue housekeeping rail. A rail feeding a device with a tight minimum needs a different part or a check against the specification of the load.

Dropout of 415 mV at 50 mA sets the input floor for a 3.0 V output. A 3.3 V input has 300 mV of headroom and the part is therefore in dropout at full load, which means the output follows the input minus the dropout and the regulation loop is open. That is acceptable for a battery product near end of discharge and wrong for a rail that has to hold 3.0 V. A 5 V input gives 2 V of headroom and full regulation.

The 0.47 microfarad minimum is a stability limit, not a recommendation. Below that value the loop is not guaranteed stable with this part, and a board that fits 100 nanofarad because the load is close will oscillate. Above it, any ceramic works, and the effective capacitance after bias derating is what counts: a 0.47 microfarad 6.3 V part at 3 V still has most of its value, which is why the small case sizes are usable here.

Quiescent current that does not grow with load is the battery number. At 3.2 microamp across the range, the draw of the regulator is negligible next to a sleeping microcontroller. The parts that fail this test are the ones whose quiescent current doubles at full load, where a rail that runs at 40 mA for a second every minute pays for it in average current. This one does not.

A 24 V input with a 3 V output at 50 mA dissipates 1.05 W. That is far beyond what a five pin SC70 can carry: the junction to ambient resistance in that body is on the order of 300 degrees per watt, so 1.05 W is a 300 degree rise. The part is rated for the voltage, not for that combination of voltage, current and drop at the same time. High input and high current together need a switching regulator, and this part is for the low current branch.

The marking is three characters and the body is 2 mm across. Incoming inspection on a reel of SC70 parts relies on the label, not the marking, because the code is shared across the family and reads differently under different lighting. A board that fits a 3.3 V member where a 3.0 V member was intended produces a rail that is 10 per cent high, which many loads tolerate and some do not.

What to confirm before this part goes on a purchase order

State the input voltage and the load current together. The 24 V rating and the 50 mA rating are separate limits, and a 24 V input at 50 mA is thermally impossible in this body.

Say whether the output feeds a device with a minimum supply above 2.9 V. Four per cent down from 3.0 V is 2.88 V, and that decides whether this part is acceptable at all.

Where this order code fits

It drops a 24 V industrial bus or a 12 V battery rail down to 3.0 V for a sensor, a real time clock or a microcontroller that sleeps for months at a time. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Can it run directly from a 24 V industrial bus? Electrically yes, with the caveat that the 24 V figure is the ceiling of the older silicon and the newer chip is rated to 30 V. Thermally only at low load: at 24 V in and 3 V out, every milliamp of load dissipates 21 mW in the part, so 20 mA is already 0.42 W in a five pin body.

How much output capacitance does it need? At least 0.47 microfarad for stability. More is allowed and improves transient response, and there is no upper limit beyond the inrush the input supply can deliver at power up. A ceramic part is the usual choice because the loop is stable with low ESR.

Is the quiescent current really 3.2 microamp at full load? The data sheet specifies 3.2 microamp typical and 4.8 microamp maximum across the load range, so the answer is yes within that window. A board measuring more should look at leakage in the output capacitor and at the sleep current of the load before blaming the regulator.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.