Contact Us

TPS71501DCKR

Brand: Texas Instruments
Texas Instruments TPS71501DCKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS71501DCKR — Power Management & Signal Chain | Superb Automation

TPS71501DCKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS71501DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS71501DCKR: 50 mA, 24 V adjustable LDO with 3.2 uA quiescent current in a 5 pin SC70 body

TPS71501DCKR is a wide input, very low quiescent current regulator for rails that have to survive a 24 V bus and stay alive with almost no standing drain in a SC70 body of 5 pins. It runs from 2.5 V to 24 V, supplies 50 mA, and draws 3.2 uA of ground current across the whole load range. The adjustable member sets any output from 1.205 V to 15 V, dropout is 415 mV typical at 50 mA, and the stable output capacitor window starts at 0.47 uF. Accuracy is plus or minus 4 per cent, which is the trade for the quiescent current.

Order code and package

TPS71501DCKR5 pin SC70 (DCK), 3000 pieces on a large reel, marking ARB, moisture level 1 unlimited
TPS71501DCKRG4same part with the green material declaration, 3000 pieces on a large reel
TPS71501DCKRM3same silicon in the small reel packing, marking ARD
Adjustable output range1.205 V to 15 V from the external divider on the feedback pin
Operating temperatureminus 40 C to plus 125 C junction, all rows carry the same grade

Electrical parameters that decide the application

Input voltage2.5 V to 24 V operating, and 30 V maximum on the new silicon only
Output voltage1.205 V to 15 V adjustable
Output current50 mA maximum continuous
Quiescent current3.2 uA typical, 4.2 uA maximum on the legacy chip and 4.8 uA maximum on the new chip
Dropout voltage415 mV typical and 525 mV maximum on the new chip at 50 mA, 750 mV maximum on the legacy chip
Output accuracyplus or minus 4 per cent over the full temperature range, with the divider tolerance excluded
Output noise575 uVRMS on the legacy chip and 425 uVRMS on the new chip over 200 Hz to 100 kHz with a 10 uF output capacitor
Rejection60 dB at 100 kHz, which is modest and is why a bypass capacitor matters
Current limit90 mA minimum and 750 mA maximum on the new chip, 125 mA to 750 mA on the legacy chip
Output capacitor0.47 uF minimum, and the stable window assumes a ceramic part

Where the two silicon generations part company

Input ceiling24 V on the legacy chip against 30 V on the new chip, and the 24 V operating limit in the table applies to both
Dropout at 50 mA415 mV typical on both, but 750 mV maximum on the legacy chip against 525 mV on the new one
Noise575 uVRMS legacy against 425 uVRMS new, a 26 per cent improvement that shows on an audio rail
Ground current4.2 uA maximum legacy against 4.8 uA maximum new, a small step in the wrong direction
Reverse currentthe new chip adds a reverse current limit that the earlier document did not specify
Package and pinoutidentical across both, so a board can see either generation without a change

Points to check before this part goes on a BOM

The 3.2 uA quiescent current is the reason to pick this part and the 4 per cent accuracy is the price. A regulator that holds 3.2 uA from zero to 50 mA of load is doing something clever with the pass element bias, and that same arrangement is what limits the reference accuracy. On a 5 V rail, plus or minus 4 per cent is 200 mV of spread, which is fine for a relay coil or an LED string and not fine for a reference input.

The input range reaches 24 V and the new silicon reaches 30 V, but the dropout row assumes the output is below the input by at least 415 mV. At 20 V in and 15 V out the part dissipates 250 mW at 50 mA, and the SC70 body has a junction to ambient around 300 C per watt on a small pad, which is not survivable. The wide input range is for transients and for a 24 V bus feeding a low output, where the dissipation stays small.

The output noise of 575 or 425 uVRMS is high compared with a modern low noise regulator, and it is a direct consequence of the tiny bias current. The pass element runs at microamps of quiescent current, so its transconductance is low and the loop has to be slow. A 0.1 uF bypass capacitor on the output, on top of the 0.47 uF minimum, is the practical mitigation and the vendor curve shows the improvement.

The 60 dB rejection at 100 kHz is the number that decides whether this part can sit behind a switching converter. A 500 kHz switcher with 20 mV of ripple and 60 dB of rejection leaves 20 uV at the output, which sounds good until the rejection falls further at the higher harmonics. The part is a post regulator for a noisy bus in a low current branch, not a ripple eliminator for a rail that has to be clean.

The minimum output capacitor of 0.47 uF is small and the part is stable with ceramic, which makes it easy to fit into a 2 mm by 2 mm area. The catch is that the ESR window matters: a 0.47 uF capacitor with a very low ESR can push the loop into a condition where the transient rings, and the vendor's own curves are measured with 1 uF. Fitting 1 uF costs nothing in a 0402 and removes the question.

The reverse current limit on the new chip is easy to miss and it matters on a bus that can be back fed. When the output is held above the input by another source, the older silicon had no specified behaviour and could draw current backwards through the body diode. The new chip limits it, so a board that can be programmed while powered from a second supply is safer with the later generation.

Both generations share the package and the pinout, so a reel cannot be screened by looking at the part. The electrical differences are in the noise, the dropout maximum and the input ceiling, and the only way to know which generation is on the board is to measure it. An incoming inspection plan that calls out the noise figure is the practical control.

Where this order code fits

It keeps a housekeeping rail alive on a 24 V industrial bus, powers a microcontroller in a metering or sensor node that sleeps for weeks, and supplies the analogue branch of a product where the standing drain is more important than the last per cent of accuracy. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Can it run from a 24 V industrial bus? Yes, 24 V is inside the operating range and the new silicon is rated to 30 V maximum. The dissipation at 50 mA and a 15 V output is the real limit, not the voltage.

Why is the accuracy only 4 per cent? Because the bias current is 3.2 uA. A regulator that draws microamps cannot also hold a 1 per cent reference over temperature. Use it for loads that tolerate the spread, or trim the divider.

Is the 24 V rating the same as a 30 V rating? No. The legacy chip stops at 24 V and the new chip is rated to 30 V maximum. A 28 V transient is only safe on the later generation.

What output capacitor is needed? 0.47 uF ceramic minimum, with 1 uF the value the vendor curves use. Adding a 0.1 uF bypass lowers the output noise noticeably.

Does it have thermal shutdown? The protection is current limit and thermal shutdown, both non latching. On a small SC70 body the thermal path is the limit and the copper under the part sets it.

Can the output be taken to 15 V from a 16 V input? Not at 50 mA. The dropout of 415 mV typical and 525 mV maximum leaves 1 V of headroom at 16 V, so the part runs in regulation, but the dissipation and the accuracy both have to be checked.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Safety Stock Planning page sets out the checks that keep a substitute from failing on the bench.