Contact Us

TPS71202DRCR

Brand: Texas Instruments
Texas Instruments TPS71202DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS71202DRCR — Power Management & Signal Chain | Superb Automation

TPS71202DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS71202DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS71202DRCR: dual 250 mA ultralow noise LDO with both outputs adjustable in a 10 pin 3 mm SON

TPS71202DRCR is a two channel RF low dropout regulator with a 1.225 V reference, 65 dB of rejection at 10 kHz and about 33 microvolt of noise on a 2.8 V output once a noise reduction capacitor is fitted in a SON (DRC) body of 10 pins. It runs from 2.7 V to 5.5 V, sources 250 mA from each channel, and drops 125 mV typical at full current. The two channels have independent enable pins and independent current limits, the shutdown current is 0.3 microamp and the ground pin current with both channels loaded is 300 microamp.

Order code and package

Order code read outTPS71202 DRC R: regulator TPS71202 with both outputs adjustable, DRC ten pin 3 mm SON, R large tape and reel
PackageSON (DRC), 10 pins, 3.0 mm by 3.0 mm by 1.0 mm, exposed pad on the underside, part marking ARQ
Carrier in the vendor addendumTPS71202DRCR at 3000 pieces on a reel; TPS71202DRCT is the same part in a 250 piece reel
Moisture levelThe addendum lists the DRC body with the standard reflow rating for the family; the reel is sealed with desiccant and the floor life is stated on the bag label
Temperature rangeJunction minus 40 to plus 125 degrees specified, minus 40 to plus 150 absolute maximum
Absolute maximum6.0 V on VIN and on the outputs, enable pins from minus 0.3 V to VIN plus 0.3 V, output current internally limited and indefinite short circuit allowed
ESD rating2 kV human body model and 500 V charged device model

Electrical parameters that decide the application

Input range2.7 V to 5.5 V, with the reference tested at 3.0 V for the adjustable versions
Reference1.200 V minimum, 1.225 V typical and 1.250 V maximum, which is plus or minus 2 percent before the divider is counted
Output rangeFrom the reference voltage up to 5.5 V minus the dropout, so a 1.8 V or 2.8 V rail is set by a divider and a 5 V rail is possible from a 5.5 V input only at light load
AccuracyPlus or minus 1.5 percent at 25 degrees with no load, and plus or minus 3 percent over the full input, load and temperature range
Output current250 mA per channel, with an output current limit of 400 mA minimum, 600 mA typical and 800 mA maximum at 90 percent of nominal output
Dropout125 mV typical and 230 mV maximum at 250 mA on each channel, measured at an input 100 mV below nominal
Ground pin current190 microamp typical with one channel enabled, 300 microamp with both channels at any load from 1 mA to 250 mA, and 600 microamp maximum
Shutdown current0.3 microamp typical and 2.0 microamp maximum with both enable pins below 0.4 V
Output noise11.8 microvolt rms per volt of output with a 0.01 microfarad noise reduction capacitor at 250 mA, which is about 33 microvolt rms on a 2.8 V rail, against 80 microvolt rms per volt with no capacitor
Rejection65 dB at 100 Hz and 65 dB at 10 kHz at 250 mA, the figure that matters for a rail feeding a radio or a converter
Start-up60 microseconds to reach 2.85 V into a 30 ohm load with a 0.001 microfarad noise reduction capacitor
Line regulation0.05 percent per volt across the specified input range
Thermal49.6 degrees per watt junction to ambient for the ten pin DRC body, 5.2 degrees per watt junction to case at the bottom

The six members of the family and the pins that change behaviour

TPS71202both outputs adjustable, the part on this page, marking ARQ
TPS712191.8 V on the first output and adjustable on the second, marking ARW
TPS712292.8 V on the first output and adjustable on the second, marking ARU
TPS71247 and TPS71257fixed pairs at 1.8 V with 2.85 V, and 2.85 V with 2.85 V, for boards that need two clean rails from one package
NR pinthe noise reduction pin; the capacitor fitted there sets the noise and the start-up time, and a 0.01 microfarad part gives the 11.8 microvolt figure quoted above

Points to check before this part goes on a BOM

Two 250 mA LDOs in one 3 mm package are usually chosen for a radio front end, and the numbers that decide the choice are the rejection and the noise rather than the current. At 65 dB from 100 Hz to 10 kHz the part removes about a factor of 1800 of input ripple, so a 20 mV ripple on a 5 V bus becomes roughly 11 microvolt at the output. That is the figure to compare against the supply rejection a sensitive VCO or PLL actually needs, not the headline dropout.

The noise reduction pin is not optional if the quoted noise matters. With no capacitor the output noise is 80 microvolt rms per volt of output, and with a 0.01 microfarad capacitor it drops to 11.8 microvolt rms per volt, which on a 2.8 V rail is about 33 microvolt against 224 microvolt. The same capacitor also slows the start-up ramp, so a board that needs a very fast turn on should use the 0.001 microfarad value and accept slightly more noise.

The dropout figure of 125 mV typical at 250 mA is quoted with a 100 mV undervoltage on the input, which is the condition that makes it a real number rather than an ideal one. A 3.0 V rail from a 3.3 V bus therefore has 300 mV of headroom against a 230 mV maximum dropout, which is enough at room temperature but leaves almost nothing at the cold end where the pass device resistance rises and the bus sags.

The current limit is set at 600 mA typical for a 250 mA channel, which is a factor of 2.4 rather than the 1.3 or 1.5 seen on many LDOs. That is deliberate for a regulator that may have to charge a large output capacitor at start up without entering current limit and dropping the rail, and it also means a shorted output passes 600 mA until the thermal path catches up rather than folding back immediately.

Ground pin current of 300 microamp with both channels loaded is high for a modern LDO and low for a 2004 vintage RF part. On a mains powered instrument it is irrelevant; on a battery powered handheld it is the dominant standing loss, and a part with a 1 microamp quiescent current would be a better fit. The shutdown current of 0.3 microamp is the number that matters for a rail that is switched off most of the time.

The ten pin SON with an exposed pad at 49.6 degrees per watt is comfortable at 250 mA from a 5 V input to a 2.8 V output, where the part dissipates about 0.55 W per channel and 1.1 W with both loaded, giving a rise of roughly 55 degrees. A build that runs both channels at full current inside a sealed enclosure at 85 degrees ambient is at the edge, and the board copper under the pad is what decides whether it stays inside the junction rating.

Where this order code fits

Feeds cellular and cordless phone front ends, wireless PDAs and handhelds, wireless LAN cards, digital cameras and audio players, and the analogue and RF rails of DSP, FPGA and converter based boards that need two clean supplies from one package. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the RF Component Sourcing page.

Questions buyers ask

What is the output voltage of the TPS71202? It is the adjustable member of the family, so both channels are set by a divider against a 1.225 V reference and can be anything from the reference up to 5.5 V minus the dropout. The fixed members are the 71219, 71229, 71247, 71256 and 71257.

How much noise does it produce? About 11.8 microvolt rms per volt of output with a 0.01 microfarad noise reduction capacitor, so roughly 33 microvolt rms on a 2.8 V rail at 250 mA. Without that capacitor the figure is 80 microvolt rms per volt.

What dropout should be budgeted? 125 mV typical and 230 mV maximum at 250 mA, measured against an input 100 mV below nominal. A 3.0 V rail from 3.3 V therefore has 300 mV of headroom, which is enough at room temperature but tight when cold.

What happens on a shorted output? The current limit is 400 to 800 mA at 90 percent of nominal output, and the short circuit is rated as indefinite, so the part stays in limit until the junction temperature rises and thermal shutdown acts.

Are the two channels independent? Yes. Each has its own enable pin and its own current limit, and the outputs can be set to different voltages with separate dividers. Both share the input pin and the ground.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.