TPS70939DBVR
Product Specifications
TPS70939DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS70939DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS70939DBVR: a 3.9 V 150 mA regulator rated to 30 V of input with 1 microamp of quiescent current
TPS70939DBVR is a fixed 3.9 V linear regulator with reverse current protection and a shutdown current of 150 nA in a SOT-23 (DBV) body of 5 pins. It regulates from 2.7 V to 30 V of input, which puts a 12 V or 24 V industrial line, a 4 cell alkaline pack and a 5 V bus inside the same part. Output is fixed at 3.9 V with 2 per cent accuracy over temperature, the peak output is 200 mA against a 150 mA continuous rating, and quiescent current is 1 microamp with 150 nA in shutdown. Reverse current protection stops the output from feeding back into a supply that has collapsed, thermal shutdown and current limit are both inside, and the body is the 5 pin SOT-23 of 2.9 mm by 1.6 mm.
Order code and package
| TPS70939DBVR | the 3.9 V member in the 5 pin SOT-23 body, 250 pieces on a small reel with marking SIC, while the .A and .B rows of the same string print a 3000 piece large reel with marking SID, so the reel size is confirmed on the packing list |
| TPS70939DBVT | the same 3.9 V die in the same body on the other carrier, which the addendum prints as 3000 pieces on one row and 250 on another, the same printing inconsistency seen across this family |
| TPS70930 and TPS70933 | the 3.0 V and 3.3 V members, same rating and same bodies, which are the strings a 3.3 V logic rail orders instead of the 3.9 V part |
| TPS709 with adjustable output | the family also ships with a feedback pin for a divider, and those members carry a 1.2 V reference, so a rail between the fixed steps is built with two resistors rather than a different part |
| WSON-6 body | the second body option, 2.0 mm by 2.0 mm, with the same die and the same electrical table but a better thermal path for a board that runs the part near its current limit |
| Pin 4 | the enable pin on the SOT-23 body, active high, with the part in shutdown at 150 nA when it is pulled low |
Electrical parameters that decide the application
| Input voltage | 2.7 V to 30 V recommended, with 36 V as the absolute maximum, so a 24 V industrial rail with a transient has to be checked against the clamp rather than the operating window |
| Output voltage | 3.9 V fixed on this code, from a family table that runs 1.2 V to 6.5 V |
| Output current | 150 mA continuous with a 200 mA peak, so a load that pulls a burst of current on a radio transmit slot is inside the peak figure but not inside the continuous one |
| Quiescent current | 1 microamp typical into the ground pin with no load, which is the figure that keeps a battery powered smoke detector alive for a decade |
| Shutdown current | 150 nA typical with the enable low, which is low enough that a board with several such regulators can be left in a shipping box for a year |
| Accuracy | 2 per cent over temperature, line and load, which is a logic rail figure rather than a reference figure |
| Dropout voltage | under 300 mV at 150 mA on the low voltage members, so a 3.9 V output needs about 4.2 V of input at full load and holds regulation from a 4 cell alkaline pack for most of its curve |
| Reverse current protection | the pass element blocks current from output back to input, which keeps a charged output capacitor from discharging into a supply that has been switched off |
| Current limit | an internal limit protects the pass element during a fault, and the output recovers when the fault clears rather than latching off |
| Thermal shutdown | junction overtemperature turns the pass element off and the part restarts when it has cooled, which is the protection that matters in the SOT-23 body at 150 mA |
| Enable pin | active high, with the part regulating when the pin is above its threshold and drawing 150 nA when it is low |
| Temperature | minus 40 C to 125 C junction over the electrical table, which covers an outdoor enclosure and an industrial cabinet with one order code |
Where this member sits in the TPS709 range
| TPS70939DBVR | this order code, 3.9 V fixed in the 5 pin SOT-23, printed on a 250 piece small reel with marking SIC on the plain row and a 3000 piece large reel with marking SID on the .A row |
| TPS70930 and TPS70933 | the 3.0 V and 3.3 V members, same rating, same bodies, same table, so the rail voltage alone decides the string |
| Adjustable members | the same family with a feedback pin and a 1.2 V reference, for a rail between the fixed steps |
| WSON-6 body | 2.0 mm by 2.0 mm, same die and same table, with a better thermal path than the SOT-23 |
| Input window | 2.7 V to 30 V, which puts a 12 V or 24 V industrial line and a 4 cell alkaline pack inside one part |
| Sleep current | 1 microamp typical with 150 nA in shutdown, which is the line a battery budget uses |
| Dissipation | 150 mA at 30 V of input is 3.6 W, which the body cannot carry, so the high input case is always a low current case |
Points to check before this part goes on a BOM
30 V of input is the reason this part exists. A 24 V industrial bus, a 12 V battery line during a load dump and a 4 cell alkaline pack that starts at 6.4 V all land inside the same regulator. The alternative is a switching stage in front, and on a 150 mA load that stage costs more board area than the headroom it saves.
1 microamp is a sleep current, not an operating current. At 150 mA the ground current rises with the load, as it does on every linear regulator. The figure that belongs in a battery budget is the no load one plus the load current, and the two are added rather than compared.
Reverse current protection is not a reverse polarity rating. It stops the output from feeding a collapsed input. It does not allow the input to be connected backwards, and a board that can see a reversed battery still needs a series diode or a protection device in front of the regulator.
The peak current figure is 200 mA, the continuous figure is 150 mA. A radio that transmits in slots, a relay coil and a card reader all pull a burst of current well above their average. The peak rating covers the burst if the thermal path can absorb it, and the average has to stay under 150 mA for the junction to settle.
The SOT-23 body has a thermal limit before it has an electrical one. 150 mA at 30 V of input is 3.6 W of dissipation in a 5 pin SOT-23, which no body of that size survives. The real operating point of this part is a high input voltage at low output current, or a low input voltage at the full current.
Reel rows in this family print both quantities. The plain R row of this string says 250 pieces on a small reel and the .A row says 3000 on a large reel with a different marking. A purchase order that names only the base string can be filled from either row, so the packing column has to be quoted on the offer.
A 3.9 V rail on a 4 cell alkaline pack
Four alkaline cells give 6.4 V fresh and 4.0 V near the end of life, which is a narrow window above a 3.9 V rail. The regulator holds 3.9 V until the pack reaches about 4.2 V and then follows the pack down, and the load sees a slow decline rather than a hard cutoff. That behaviour is what a metering product wants, because the microcontroller can measure its own supply and warn before the rail collapses.
The same part on a 24 V bus runs at 20 mA rather than 150 mA, because the dissipation is what limits it. On that supply the working point is a low current standby rail for a radio module or a sensor front end, not a main rail.
What reverse current protection actually saves
A board with a 3.9 V rail and a 5 V rail often has both derived from the same source, and the 5 V rail comes up first. Without blocking, the 3.9 V regulator is back fed through its own output and the current path runs through the pass element into an unpowered input. With the blocking in this family the output sits at 5 V minus a diode drop and nothing flows, which keeps the part alive through an arbitrary number of power cycles.
Where this order code fits
a 3.9 V logic or sensor rail on a 12 V or 24 V industrial line, a metering product running from a 4 cell alkaline pack, or a standby rail that has to survive a year in a warehouse Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
Can this part take 24 V directly? Yes, the recommended window runs to 30 V and the absolute maximum is 36 V. The dissipation at 24 V in and 3.9 V out is what limits the current, so at that input the part is a low current rail rather than a 150 mA one.
What is the difference from the TPS7A03 family? The TPS7A03 stops at 6 V of input, delivers 200 mA and draws 200 nA. This part takes 30 V, delivers 150 mA and draws 1 microamp, so the choice is driven by the input voltage first and the sleep current second.
Does the output stay defined when the input collapses? The output follows the input down through the dropout margin and the reverse protection stops the output capacitor from feeding back. There is no discharge circuit on this member, so a rail that must be pulled to zero needs an external path.
Is 2 per cent accuracy enough for a sensor supply? For a ratiometric sensor it is, because the sensor and the converter share the same rail. For a sensor with an absolute output it is not, and those boards use a reference or a tighter regulator.
What body options are there? The 5 pin SOT-23 of 2.9 mm by 1.6 mm and the 6 pin WSON of 2.0 mm by 2.0 mm, same die and same table, with the WSON giving the better thermal path.
How does SUPERB supply this string? With the exact ordering string, the reel quantity and the marking stated on the offer, because the plain, .A and .B rows of this part number print different carriers and different markings in the vendor addendum.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.