Contact Us

TPS70912DRVR

Brand: Texas Instruments
Texas Instruments TPS70912DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS70912DRVR — Power Management & Signal Chain | Superb Automation

TPS70912DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS70912DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS70912DRVR 1.2 V regulator rated for 30 V input

The TPS70912DRVR is the 1.2 V fixed member of the TPS709 family, a 150 mA regulator that takes up to 30 V on its input. The combination is unusual and that is the point of the part: most low dropout regulators that hold a 1.2 V rail are built on a 6 V process, and a board that has to survive a 24 V industrial bus or a 12 V battery with load dump needs a device that will not break when the input is far above the output. Quiescent current is 1 microamp, shutdown current is 150 nA, and the part is 2 percent accurate over temperature.

The body is the DRV, a six pin WSON of 2 mm by 2 mm. The family also ships in the DBV five pin SOT-23, and both bodies carry the same electrical table. Fixed outputs run from 1.2 V to 6.5 V, so one document covers a 1.2 V core rail, a 3.3 V sensor rail and a 5 V analogue rail on the same board.

The regulator carries reverse current protection and a current limit, and it has the ground current behaviour that the family is known for: when the input falls close to the output and the pass device enters its linear region, the ground current is held down instead of rising by orders of magnitude. On a 30 V part that matters twice, because the same 1 microamp that makes it usable in standby is also what keeps the dissipation inside the package when the input is at the top of its range.

Key parameters from the SBVS186H document

Input range2.7 V to 30 V
Output1.2 V fixed on this order code, 1.2 V to 6.5 V across the family
Output current150 mA rated, 200 mA peak
Quiescent current1 microamp typical
Shutdown current150 nA typical with the enable pin low
Accuracy2 percent over temperature
ProtectionReverse current, current limit and thermal shutdown
DropoutSpecified only where the output is 2.8 V or above, so the 1.2 V member is limited by its 2.7 V input floor
PackagesDBV five pin SOT-23 and DRV six pin WSON, 2 mm by 2 mm
Applications in the documentSmoke and heat detectors, thermostats, motion detectors, meters, battery packs
Order codeTPS70912DRVR, WSON body, active in the vendor addendum

What 30 V input buys and what it costs

A 30 V rating is what lets the part sit directly on a 24 V rail or a 12 V battery line without a pre regulator. What it costs is dissipation: at 30 V in and 1.2 V out, a 20 mA load puts 0.58 W into the package, which a 2 mm by 2 mm WSON can only take with a copper area under it. The 150 mA rating applies at a small input to output difference, not at the top of the input range, and any application drawing more than a few tens of milliamps from a high input should be checked against the thermal table before the rail is committed.

The other cost is the minimum input. The part needs 2.7 V to start and to regulate, so a 1.2 V output from a two cell alkaline pack that falls to 2.4 V is outside the specified range even though the pass device would still conduct. A product that runs to the end of an alkaline discharge either accepts a slightly higher output floor or uses a different member of the family with a lower input requirement.

Where this part fits

Smoke and heat detectors, thermostats, PIR and microwave motion sensors, cordless tool packs, appliance battery packs, electricity meters and water meters. All of those run from a rail well above their logic supply and all of them care about standby current. The rail is also a natural fit for a 4 mA to 20 mA loop instrument, where the 24 V bus is the input and the 1.2 V core is what the microcontroller needs. Substitution notes for the family are under power management cross reference, and the inspection steps for a 30 V part that has to survive a bench surge are in incoming inspection plan.

What to check before a purchase order

Check the output capacitor against the stable range in the document rather than copying the value from a 3.3 V rail. A regulator that is stable at 2.2 microfarad on a 3.3 V output is not automatically stable at 1.2 V, because the loop gain changes with the output voltage and the zero that the capacitor contributes moves with it. A part that oscillates at light load on a 1.2 V rail usually shows up as a slow drift in the ADC readings rather than as an obvious failure.

Check the leakage of the load against the 1 microamp quiescent current, and check the reverse current path. On a board where the 1.2 V rail feeds a device that can be powered from a debug probe, the reverse current protection is what stops the probe from charging the rail and the regulator from sinking that current. Also confirm the enable pin is not left floating: the part has no internal pull down strong enough to define the state on a humid board, and a floating enable is a common cause of a rail that starts sometimes.

Questions that come up on this part

Is there a version that starts below 2.7 V? Not in this family. The 2.7 V floor is a family specification, so a lower input needs a different part with a different process.

Can two of these be paralleled for more current? No. There is no current sharing between regulators of this type, and the one with the higher set point will carry the whole load until its current limit engages.