Contact Us

TPS65251-1RHAR

Brand: Texas Instruments
Texas Instruments TPS65251-1RHAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65251-1RHAR — Power Management & Signal Chain | Superb Automation

TPS65251-1RHAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65251-1RHAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65251-1RHAR three converter front end for a 12 V rail

The TPS65251-1RHAR is the first option of the TPS65251-x family: three synchronous step down converters with integrated switches, a 4.5 V to 18 V input, and continuous output currents of 3 A on the first converter and 2 A on the other two, with maximum currents of 3.5 A and 2.5 A. The output range is 0.8 V to just below the input, set by an external divider against a 0.8 V reference. The body is a 40 pin VQFN of 6 mm by 6 mm.

Each converter has its own enable pin, its own soft start capacitor and its own current limit resistor, so the three rails can be sequenced, ramped and limited independently. The switching frequency is set by a resistor from 300 kHz to 2.2 MHz, or the converters can follow an external clock on the SYNC pin. The first converter runs 180 degrees out of phase with the other two, and the other two run in phase with each other, which halves the input ripple for a given input capacitor.

A supervisor watches all three outputs and asserts the power good pin once the sequence is complete, all the internal power good signals are reported and a selectable reset delay has elapsed. Quiescent behaviour is automatic pulse frequency modulation at light load with a transition to PWM as the load rises.

Key parameters from the SLVSC70B document

Input range4.5 V to 18 V, 20 V absolute maximum on the switch pins
Output range0.8 V to VIN minus 1 V, set by an external divider
Output current3 A, 2 A and 2 A continuous, 3.5 A, 2.5 A and 2.5 A maximum
Switching frequency300 kHz to 2.2 MHz set by a resistor on ROSC, or an external clock on SYNC
Phase relationshipConverter 1 is 180 degrees out of phase with converters 2 and 3
Current limitSet per converter by a resistor on the RLIMx pin
Soft startSet per converter by a capacitor on the SSx pin
SupervisionPower good asserted after the sequence, all internal flags and a selectable reset delay
Light loadAutomatic pulse frequency modulation with a transition to PWM
PackageRHA 40 pin VQFN of 6 mm by 6 mm, 2500 pieces on a large reel, moisture level 3

Why the current limit resistor matters more than the rating

The three converters share one die, one input capacitor bank and one thermal pad, so the current limit setting decides where the loss lands. Setting the limit high enough to avoid a nuisance trip during a load step also sets how much current the inductor and the input capacitor have to survive during a fault. The vendor provides the pin precisely because that trade cannot be made once for every application.

The soft start capacitor follows the same logic. A fast ramp keeps the rail inside its timing window but charges the output capacitance with a current the input supply has to deliver, and on a 12 V bus with a long cable the result is a dip that resets the other two rails.

Where this part fits

Industrial controllers, set top boxes, network appliances, automotive aftermarket units and any board that takes a 12 V or 24 V bus and needs three rails with a defined order. The cross reference for this family sits under power management cross reference.

What to check before a purchase order

Check which option the board needs. The family is published as TPS65251-1, TPS65251-2 and TPS65251-3, all in the same 40 pin body, all at 2500 pieces on a large reel, and they differ in the internal option that sets the default behaviour. The addendum also prints 2500 pieces against the RHAT row, which is the code normally used for the small reel, so the quantity has to be read rather than derived from the letter.

Check the input capacitor against the 180 degree phase arrangement. Two converters in phase double the ripple at the input node, so a capacitor chosen for three independent phases will run hotter than expected. The incoming check we run for multi rail parts is in incoming inspection plan.

Questions that come up on this part

Can the frequency be changed after the board is built? Yes, by changing the ROSC resistor, within the 300 kHz to 2.2 MHz window, and the compensation network has to be rechecked against the new frequency.

Is the power good output open drain? It is, so it can be wired with other supervisors on the board, and the pull up has to sit on the rail that stays alive longest.

One more item belongs on the drawing. The three feedback dividers share one 0.8 V reference, so the tolerance of each output is set by the reference plus the divider resistors, and the vendor's 1 per cent figure is the reference alone. A rail quoted at 3.3 V with 1 per cent resistors lands inside roughly 2 per cent over temperature, which is fine for a logic rail and not fine for an analogue one that is used as a reference elsewhere on the board.