TPS6522053RHBR
Product Specifications
TPS6522053RHBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS6522053RHBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS6522053RHBR PMIC for Cortex A53 class processors and FPGAs
The TPS6522053RHBR is the pre programmed member of the TPS65220 family: three step down converters and four linear regulators in a 32 pin QFN, set up at the factory for a processor rail list and characterised across a minus 40 to plus 125 degree ambient range. The converter set is one 3.5 A rail and two 2 A rails from a 2.5 V to 5.5 V input over 0.6 V to 3.4 V, all three with dynamic voltage scaling.
The linear regulators follow the same pattern as the rest of the family: two at 400 mA with bypass and load switch modes for a card rail, and two at 300 mA over 1.2 V to 3.3 V with a load switch mode. Switching frequency reaches 2.3 MHz, the converter inductors are 470 nH, and the vendor calls for 4.7 microfarads of input capacitance and at least 10 microfarads per output rail depending on the mode in use.
The difference against the user programmable member is who owns the settings. This part leaves the factory with a fixed rail list and a fixed sequence, so the host writes the bus only when it wants to change a voltage at run time. The trailing digits of the order code identify that image, and the addendum prints the image number next to the order row rather than in words.
Key parameters from the SLVSGY1B document
| Converter 1 | 2.5 V to 5.5 V input, 3.5 A, 0.6 V to 3.4 V output, dynamic voltage scaling |
| Converters 2 and 3 | 2.5 V to 5.5 V input, 2 A each, 0.6 V to 3.4 V output |
| LDOs 1 and 2 | 1.5 V to 5.5 V input, 400 mA, 0.6 V to 3.4 V, bypass and load switch modes |
| LDOs 3 and 4 | 2.2 V to 5.5 V input, 300 mA, 1.2 V to 3.3 V, load switch mode |
| Switching frequency | Up to 2.3 MHz, power save and forced PWM selectable per rail |
| Passives | 470 nH inductor, 4.7 microfarad input capacitor, 10 microfarad minimum output per rail |
| Interface | I2C with full control of every rail, plus GPO and GPIO pins |
| Ambient range | Minus 40 to plus 125 degrees, which is the industrial grade span for this family |
| Package | RHB 32 pin VQFN, 3000 pieces on a large reel, NIPDAU finish |
| Moisture level | Level 2 with a one year floor life, per the published order row |
The ambient range is the reason for this member
Most PMICs in this class stop at 85 or 105 degrees ambient. This one is characterised to 125 degrees, which is what a fanless enclosure in an industrial cabinet or under a vehicle dash needs once the processor and the memory are added to the thermal budget. The converters are the same silicon as the rest of the family, so the higher rating is a specification and test decision rather than a different die.
That matters at the purchasing desk because a board that was released on an 85 degree member can be moved to this one without changing the copper, the inductor or the output capacitors, provided the thermal pad and the surrounding copper are sized for the higher dissipation.
Where this part fits
Single board computers, industrial gateways, panel controllers, FPGA carrier boards and processor modules that need a defined rail list and a sequence set at the factory. The cross reference for this class sits under power management cross reference and one stop BOM sourcing.
What to check before a purchase order
Check the image. The order code ends in a number that selects the rail list and the sequence, and the addendum prints that number beside the row rather than decoding the rails. Two parts from the same family with different trailing digits are not interchangeable on a board even though the body, the reel and the price are the same.
Check the thermal path. A 3.5 A converter at 2.3 MHz in a 5 mm body puts most of its loss into the thermal pad, so a board with a small pad and no vias will sit well above the ambient the part is rated for. The reel and date check is in date code management.
Questions that come up on this part
Can the sequence be changed on the board? No. The sequence is part of the image, so a change means a different order code, which is exactly the property a product with a frozen rail list wants.
Do the converters need external compensation? No, the loop is internal and the vendor publishes the output capacitor windows per rail, which is what sets the minimum 10 microfarad figure.
Two assembly details belong on the drawing as well. The 32 pin body carries the heat of the 3.5 A rail through its exposed pad, so the pad needs a via array into a ground plane rather than a single trace under the part. The second is the output capacitor window per rail: the vendor states a minimum of 10 microfarads, and the actual value follows the mode the rail runs in, so a board that switches a rail between power save and forced PWM has to be checked in both modes rather than in one.