Contact Us

TPS65105PWPR

Brand: Texas Instruments
Texas Instruments TPS65105PWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65105PWPR — Power Management & Signal Chain | Superb Automation

TPS65105PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65105PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65105PWPR: triple output supply for TFT LCD panels with a linear regulator controller and a VCOM buffer

TPS65105PWPR is one chip that produces the three rails a thin film transistor panel needs, the source driver voltage, the gate high voltage and the gate low voltage in a HTSSOP (PWP) body of 24 pins. It runs from 2.7 V to 5.8 V in, switches at a fixed 1.6 MHz, boosts to as much as 15 V at 350 mA with under 1 per cent accuracy, and derives a negative rail and a positive charge pump rail from the same inductor, so a panel bias supply becomes one part and about two dozen passive components.

Order code and package

Ordering stringTPS65105PWPR, the HTSSOP body on a 2000 piece large reel
Body24 pin HTSSOP, 7.80 mm by 4.40 mm, with the PowerPAD on the underside
Second body24 pin VQFN, 4.00 mm by 4.00 mm, same die and same pinout under the RGE code
FamilyTPS65100, TPS65101 and TPS65105, separated by the boost switch current limit and by the linear regulator configuration
This memberTPS65105 carries a 0.96 A switch current limit against 1.6 A on the other two, which is what suits a panel that draws a few hundred milliamps rather than a full monitor load
Input range2.7 V to 5.8 V, so a single lithium cell or a 5 V rail feeds it directly
OutputsA boost rail up to 15 V, a regulated negative charge pump rail, a positive charge pump rail and an auxiliary linear regulator

Electrical parameters that decide the application

Switching frequency1.6 MHz fixed, which keeps the inductor in the few microhenry range and the output ripple small enough for a panel bias rail
Boost output5 V to 15 V, with the input to output difference held above 1 V, and under 1 per cent output accuracy
Boost current350 mA at the boosted rail, limited by the 0.96 A switch on this member
Reference1.213 V typical, 1.205 to 1.219 V, used by the boost feedback divider
Feedback regulation1.146 V typical, 1.136 to 1.154 V on the main feedback pin
Quiescent current0.7 mA typical and 0.9 mA maximum with the boost not switching, 1.7 mA typical on the charge pump supply
VCOM buffer3.9 mA typical and 6 mA maximum from the supply, driving the panel common electrode
Linear regulator controller750 uA typical and 1.3 mA maximum, driving an external pass transistor for a 3.3 V logic rail from a 5 V input
Shutdown current1 uA typical, 10 uA maximum, with both enable pins low
Undervoltage lockout2.4 V typical on a falling input
Thermal shutdown160 degrees junction
Logic thresholds1.5 V minimum for a high on the enable pins, 0.4 V maximum for a low

Family variants and how they differ

TPS65100 and TPS65101The 1.6 A switch members for panels that need more source driver current, with the same three rail architecture
TPS65105The 0.96 A member on this page. Same silicon family, lower switch limit, which lets a smaller inductor and a cheaper flying capacitor set be used
Negative charge pumpDriven from the boost switch node, so the negative rail tracks the boost rail and needs no second inductor. Its magnitude is set by the feedback divider on the second feedback pin
Positive charge pumpDoubles or triples the boost rail to give the gate turn on voltage, set by the number of flying capacitors fitted
VCOM bufferAn internal amplifier that buffers a resistor divider or an external digital to analogue converter output to drive the panel common electrode, which is a capacitive load of tens of nanofarads
Auxiliary linear controllerDrives an external PNP or P-channel pass device so the same chip can make a 3.3 V logic rail, useful when the only input is 5 V

Points to check before this part goes on a BOM

The three rails share one inductor, so the negative and positive pump outputs track the boost rail rather than being independent. A panel that needs the negative rail to come up before the positive one needs an external sequence, not a different setting on this chip.

The 1.6 MHz switching frequency is fixed and cannot be synchronised. On a board with a sensitive radio or an ADC, the switching harmonic at 3.2 MHz and beyond has to be kept away from the analogue front end by filtering rather than by moving the clock.

Switch current limit differs by family member: 0.96 A here against 1.6 A on the TPS65100 and TPS65101. A 350 mA boost load is fine; a panel that pulls half an amp from the boost rail is not, and the part will fold back rather than deliver it.

The VCOM buffer draws up to 6 mA from the supply and drives a capacitive load. Its output is meant for a common electrode at a fixed or slowly adjusted voltage, not for a signal that changes every line.

The linear regulator controller drives an external pass device. Its dropout is set by that device, not by the chip, so the 3.3 V rail headroom depends on the transistor chosen.

Quiescent current is milliamps, not microamps. This is a panel supply that is on when the display is on, and it is turned off by the enable pins when the product sleeps.

What the three panel rails do

A TFT panel needs a source driver supply, usually 8 to 15 V, a gate turn on voltage above that, and a gate turn off voltage below ground. The boost converter makes the source rail, a charge pump stacked on the switch node makes the negative rail, and a second pump doubles or triples the boost for the gate high rail. One inductor, one switch node, three outputs.

The reason a single chip is preferred over three converters is not only board space. The three rails have to come up in a defined order and stay in proportion, and a chip that generates all of them from one switch node has that relationship built in.

Where this order code fits

Small and medium TFT panels in industrial instruments, portable medical displays, test equipment, point of sale terminals and automotive cluster displays. The panel needs a boost rail for the source drivers, a negative rail for gate turn off and a positive rail above the boost for gate turn on. Doing that with three separate converters costs board area and three inductors; this part does it with one inductor and two flying capacitor pumps. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can this part drive a 10 inch panel? Only within its 350 mA boost budget and the 0.96 A switch limit. Larger panels draw more source driver current and need the 1.6 A members of the family or a separate boost converter.

What sets the negative rail voltage? A divider on the second feedback pin. The charge pump is driven from the boost switch node, so the negative rail magnitude is a ratio of the boost rail plus the divider setting.

Is an external inductor needed for each rail? No. One inductor on the boost switch node supplies all three rails, and the pumps transfer charge through flying capacitors.

How is brightness or contrast adjusted? Through the VCOM voltage, which is normally set by a divider or by a small DAC into the buffer, and through the panel's own gamma network. This chip supplies the rails, not the gamma voltages.

What happens if the panel is disconnected while the supply runs? The boost rail loses its load and rises until the feedback loop reacts, and the pumps follow. A panel connector that can be unplugged in service should have the supply disabled first, or an overvoltage clamp on the boost rail.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.