TPS650944A0RSKR
Product Specifications
TPS650944A0RSKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS650944A0RSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS650944A0RSKR: six rail PMIC for Intel Apollo Lake class platforms
TPS650944A0RSKR is a single chip power management IC for 2, 3 and 4 cell battery platforms built on the Apollo Lake rail map in a VQFN (RSK) body of 64 pins. It carries the same six regulator architecture as the Braswell sibling but splits the current differently, puts 21 A behind the VCCGI controller, and moves the VDDQ default into one time programmable memory instead of a pin strap.
Order code and package
| Order code read out | TPS650944 A0 RSK R: family and OTP image TPS650944, A0 default, RSK 64 pin VQFN, R large tape and reel |
| Package | VQFN (RSK), 64 pins, 8.00 mm by 8.00 mm with thermal pad |
| Carrier | 2000 pieces on a large reel, the row the addendum publishes for this family |
| Operating temperature | minus 40 to plus 85 degrees Celsius ambient |
| Moisture and finish | MSL level 3, 260 degrees peak reflow, 168 hour floor life, NIPDAU |
| Control interface | I2C at 0x5E, 100 kHz, 400 kHz and 1 MHz |
| Siblings in the same table | TPS650940, 941, 942, 945 and 947, each a different OTP image in the same 64 pin body |
Electrical parameters that decide the application
| Controller input | 5.6 V to 21 V for BUCK1, BUCK2 and BUCK6 |
| Converter input | 4.5 V to 5.5 V for BUCK3, BUCK4 and BUCK5 |
| BUCK1 VNN | 5 A with external FETs, D-CAP2 control, DVS from 0.5 V to 1.45 V in 10 mV steps |
| BUCK2 VCCGI | 21 A with external FETs, the graphics rail and the largest current in the set |
| BUCK6 VDDQ | 7 A with external FETs, default voltage one time programmable rather than pin strapped |
| BUCK3 VCCRAM | 3 A integrated |
| BUCK4 V1P8A and BUCK5 V1P24A | 2 A each integrated |
| LDOA1 | 1.35 V to 3.3 V at 200 mA, I2C selected, the 0100 code gives 1.8 V on this image |
| LDOA2 and LDOA3 | 0.7 V to 1.5 V at 600 mA each, wider range and three times the current of the Braswell LDOs |
| Load switches | 400 mA each with slew rate control, drop under 1.5 percent of nominal input, on resistance under 96 milliohm at 1.8 V |
| VTT rail | sink and source termination rail for DDR3 and DDR4 |
| Load switch on resistance | under 96 milliohm at a 1.8 V input, 400 mA rating per switch |
| VTT termination | sinks and sources current, so it tracks VDDQ in both directions as the memory bus switches |
Family variants and how they differ
| TPS650944 | the image on this page, 21 A VCCGI and 5 A VNN |
| TPS650940 to 942 | adjacent images in the same table, different default rails for other platform variants |
| TPS650945 and 947 | the remaining images, one of which changes the LDOA1 default code |
| TPS650842 | the Braswell generation, same body size, different current split and a pin strapped VDDQ |
| Practical effect | the six images are not interchangeable in a build, because each one powers up in a different order |
| OTP programming | the default rail set is burned at the factory, so it cannot be changed on the board |
Points to check before this part goes on a BOM
The letter block is the rail map. Six images, TPS650940 through TPS650947, share the 64 pin body and differ in default voltages, power up order and which rails are enabled at reset. A purchase order that names only the family invites the wrong image, and the error shows up as a board that boots into the wrong sequence, which is hard to trace on a production line.
The 21 A rail is a controller, not a converter. BUCK2 VCCGI drives external FETs, so the 21 A figure is what the controller can regulate, and the FET pair, the inductor and the copper decide what the rail survives. Datasheet efficiency curves for this rail are drawn with specific FETs, and a cheaper pair moves the whole thermal picture.
The two LDOs on this image are wider and stronger than the Braswell ones. 0.7 V to 1.5 V at 600 mA each covers rails that the earlier part could not reach at that current, which is why a board moved from TPS650842 to TPS650944 changes its LDO loading assumptions. A 1.2 V rail at 550 mA is inside the new limit and outside the old one.
DDR4 and DDR3L both work, but the memory strap and the OTP image must agree. VDDQ is programmed rather than strapped here, so the memory generation is fixed at the factory. A build that changes memory type needs a different image, not a resistor change.
The document is long and current. SWCS133F was revised in January 2025, which is unusual for a 2015 platform part and means the vendor has kept the electrical tables current. That revision history is worth reading before a customer claims an older revision as the reference.
The 21 A rail is the one that decides the board. BUCK2 VCCGI drives external FETs and carries the largest current in the set, which means the FET pair, the inductor and the copper under them are the real limit. Vendor efficiency curves for this rail are drawn with a specific pair, and substituting a cheaper FET with higher gate charge moves the loss into the controller and the switching band.
The two wide range LDOs change what the board can be built with. 0.7 V to 1.5 V at 600 mA covers rails that the Braswell generation could not reach at that current, so a platform refresh can drop a separate LDO. The lower bound of 0.7 V is also the floor, and a 0.65 V rail, which some memory technologies ask for, is outside it.
MSL level 3 with a 168 hour floor life is a production constraint, not a footnote. These 8 mm bodies absorb moisture, and a board that sits on the line for a week after the reel is opened needs a bake before reflow or the package will crack. The parts arrive dry packed, and the label date is what the line should work from.
The three integrated converters run from the 5 V system rail, not from the battery. BUCK3, BUCK4 and BUCK5 accept 4.5 V to 5.5 V, so the 5 V rail has to exist before they can start, and it comes from BUCK5P0 or from an external supply depending on the platform. A board that expects these rails to come up from the battery alone will sequence fault, because the state machine waits for a rail that is not there yet.
Where this order code fits
The part serves industrial and embedded boards that pair an Apollo Lake class processor with DDR memory, from panel PCs and digital signage to gateway boxes and medical carts, where one package has to deliver six rails in a fixed order. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Is TPS650944 a drop in for TPS650842? The body and pin count match but the rail currents, the VDDQ method and the LDO ranges do not. Treat it as a family relative that needs a rail by rail check, not as a substitute.
Which image should a repair order ask for? The one printed on the board or in the original build documentation. If that is unknown, the platform reference rail map decides it, and we will ask for the processor generation and the memory type.
Do you stock the 2000 piece reel? We source it against the order. The offer states reel size, date code, country of origin and whether the parts come from a franchised channel or the open market.
How do I know which image a board needs? From the platform rail map and the memory type. The image letter fixes the default voltages and the power up order, and the board documentation or the original build file names it.
Does the part need external FETs for every rail? Only for BUCK1, BUCK2 and BUCK6. BUCK3, BUCK4 and BUCK5 are integrated converters with their switches on the die.
Is a reballed or refurbished part acceptable for repair? Only if the customer accepts it in writing. We quote new production parts by default and state the condition, the date code and the source for anything else.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.