TPS650250RHBR
Product Specifications
TPS650250RHBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS650250RHBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS650250RHBR: Power management IC, 3 converters, 3 LDOs, 1.6 A system rail, VQFN-32
TPS650250RHBR is a power management IC for a system on chip that puts three step down converters and three low dropout regulators in a 5 mm by 5 mm body in a VQFN-32 body of 32 pins. The converters are rated 1.6 A for the system rail, 0.8 A for memory and 0.8 A for the processor core, with the system rail reaching 97 per cent efficiency. A 30 mA regulator keeps the always-on domain alive and two 200 mA general purpose regulators cover peripherals. The core converter is adjustable for dynamic voltage management, and the default voltages for the other rails are chosen by the DEFDCDC pins at start up.
Order code and package
| TPS650250RHBR | Active, VQFN (RHB) body, 32 pins, 5 mm by 5 mm, 3000 pieces on a 330 mm reel in the published addendum |
| TPS650250RHBRG4 | Active, the same part with the green material row and the same 3000 piece reel |
| TPS65023RSBR | a related PMIC with a different converter set in a 40 pin body, not pin compatible |
| Temperature range | minus 40 to 85 degrees ambient |
| Default voltages | selected at start up by the DEFDCDC pins, before any bus traffic |
Electrical parameters that decide the application
| Input voltage | 2.5 V to 6 V, with the LDOs able to run from 1.5 V to 6.5 V |
| System converter | 1.6 A at up to 97 per cent efficiency, fixed 3.3 V or 2.8 V or adjustable |
| Memory converter | 0.8 A at up to 95 per cent efficiency, fixed 1.8 V or 2.5 V or adjustable |
| Core converter | 0.8 A at up to 90 per cent efficiency, adjustable for voltage management |
| Always-on regulator | 30 mA for the keep-alive domain |
| General purpose LDOs | two 200 mA regulators, adjustable |
| Reference | a 0.6 V reference sets the adjustable output range |
| Reset | externally adjustable delay for the processor |
Family variants and how they differ
| TPS650250 | three converters and three LDOs, the string on this page |
| TPS65023 | a 40 pin PMIC with different converter currents and an I2C interface |
| Converter count | three step down stages, so the core, the memory and the system rail each have their own |
| LDO inputs | each LDO can be fed from a converter or from the battery, which changes the dissipation |
| Package | 32 pins in a 5 mm by 5 mm body with an exposed pad for the thermal path |
Points to check before this part goes on a BOM
The system converter at 1.6 A is the workhorse of this part. It runs the I/O rail, which on most boards is the largest load and the one that is always on. At 97 per cent efficiency from a 5 V input to a 3.3 V output the loss is small enough that the converter does not dominate the thermal budget of the 5 mm body, which is what allows the other five rails to share it.
The memory rail and the core rail are deliberately small. Eight hundred milliamps each covers a mobile memory and a modest applications processor. A board that needs 1.5 A on the core is outside this part and outside the pin out, and the larger member of the family is the answer. Quoting this part into a board that needs more current produces a rail that sags under load rather than a clean failure.
Default voltages decide whether the board starts at all. The DEFDCDC pins set the system and memory rails before any processor traffic. A processor whose I/O rail must be 3.3 V will not run if the strap selects 2.8 V, and the symptom is a board that powers up and does nothing. That is a strap error rather than a part failure, and it is the first thing to check on a new build.
Three converters in one body share one thermal path. Total dissipation is the sum of all three stages plus the LDOs, and the exposed pad is the only way out. On a 5 V input with 3.3 V, 1.8 V and 1.2 V rails all loaded the total loss can reach a watt, which in a 5 mm body requires a copper area under the pad and a continuous ground plane. A board that shares the pad with a via farm to the other side does better.
The 30 mA always-on regulator is the one that decides battery life. Everything else can be switched off, and this rail stays on to keep a real time clock and a wake circuit alive. Its quiescent current is the sleep current of the product, and its load is usually tens of microamps. A customer who compares PMICs on converter efficiency and ignores this rail is comparing the wrong number.
LDO dissipation depends on where the input comes from. A 200 mA LDO fed from the battery at 4.2 V with a 1.8 V output dissipates 0.48 W, which is a large share of the thermal budget. Fed from the 1.8 V memory rail it cannot regulate at all. The right source is usually the 3.3 V system rail, and that choice is made at the block level rather than at the part.
Forty to eighty five degrees ambient is the published range. A board that runs this part in a sealed enclosure at 70 degrees ambient has only 15 degrees left before the ambient limit, and the junction is higher still. The thermal calculation, not the current ratings, decides whether the part is usable at the top of the range.
A 32 pin body leaves no pin for a dedicated enable per rail on every stage. Some rails are sequenced by the part itself and others by external signals, and the sequence in the data sheet has to be followed. A board that forces an order different from the recommended one can produce a latch up path through the processor, which is the kind of failure that appears only on some units.
Packing is 3000 pieces on a 330 mm reel. That is a large reel for a PMIC used once per board. A prototype build of 100 pieces leaves most of the reel in stock, and the moisture sensitivity level of the body decides how long it can sit on the shelf after the bag is opened. The level is printed on the reel label and it is worth recording at goods inwards.
What to confirm before this part goes on a purchase order
State the processor and the rail voltages it needs. The default strap settings and the converter currents are chosen against a specific processor family, and a PMIC quoted without them cannot be checked.
Give the total load on each rail. The three converters share one thermal path, and the sum of the currents decides whether the 5 mm body can carry the dissipation.
Where this order code fits
It powers a system on chip and its peripherals in a single board computer or a portable instrument, with three converters and three low dropout rails in one body. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does it include a battery charger? No. It generates rails from a battery or a 5 V supply, and a product that charges a battery needs a charger in front of it. The PMIC then runs from the battery or from the system rail the charger produces.
Can the output voltages be changed after start up? The core converter is adjustable for voltage management, and the other rails are set by the strap pins at start up. Anything that has to change while running needs the core stage or a part with a bus interface.
What current can the 3.3 V system rail supply? 1.6 A. That is the largest of the three converters and it feeds the I/O domain, which is usually the biggest load. A board that needs more has to add an external converter, because the other two stages are 0.8 A each and are intended for memory and core.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.