TPS65023RSBR
Product Specifications
TPS65023RSBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS65023RSBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS65023RSBR: Power management IC, 3 DC/DC converters, 3 LDOs, I2C and DVS, WQFN-40
TPS65023RSBR is a power management IC for a processor based system that puts three step down converters, three low dropout regulators and an I2C interface in one 5 mm by 5 mm body in a WQFN-40 body of 40 pins. The converters are rated 1.7 A for the core, 1.2 A for the system rail and 1.0 A for memory, all synchronous with integrated switches. Two 200 mA general purpose LDOs and a 30 mA always-on regulator for a real time clock complete the rails. The I2C interface runs to 400 kHz and supports dynamic voltage scaling on the core converter, which is how a processor changes frequency without a second regulator.
Order code and package
| TPS65023RSBR | Active, WQFN (RSB) body, 40 pins, 5 mm by 5 mm, 250 pieces on a small reel in the published addendum |
| TPS65023BRSBR | the B revision with a different default configuration, same body and same pin out |
| TPS650250RHBR | a related PMIC with a different converter set in a 32 pin body, not pin compatible |
| Temperature range | minus 40 to 85 degrees ambient |
| Interface | I2C compatible, fast and standard mode, transfers up to 400 kHz |
Electrical parameters that decide the application
| Input voltage | 2.5 V to 6 V from a battery or a 5 V rail, with the LDOs able to run from 1.5 V to 6.5 V |
| Core converter | 1.7 A, up to 90 per cent efficient, with dynamic voltage scaling over I2C |
| System converter | 1.2 A, up to 95 per cent efficient, fixed or adjustable output |
| Memory converter | 1.0 A, up to 92 per cent efficient, fixed or adjustable output |
| LDOs | two 200 mA general purpose regulators plus a 30 mA always-on regulator for a real time clock |
| Default voltages | selected by the DEFDCDC and DEFLDO pins, so a system can start without I2C traffic |
| Reset | externally adjustable reset delay for the processor |
| Backup | battery backup functionality for the real time clock rail |
Family variants and how they differ
| TPS65023 | the base part with a fixed default set, the string on this page |
| TPS65023B | the B revision with different defaults, same silicon family and same package |
| TPS650250 | a 32 pin variant with a different converter mix, not a substitute without a board change |
| Interface pins | SCL and SDA are 5 V tolerant and can be shared with the rest of the bus |
| Enable pins | each converter has its own enable, so the start order is set by the system rather than by the part |
Points to check before this part goes on a BOM
One body with six rails removes a lot of bill of materials lines. A discrete version of this function is three buck converters, three LDOs, a sequencer and a reference, with the associated passives and the board area for all of it. The PMIC replaces that with one 5 mm square part and a handful of inductors, at the cost of a single source and a configuration that has to be understood before the board is built.
The defaults decide whether the board boots. The DEFDCDC and DEFLDO pins select the output voltages at start up, before any I2C traffic. A processor that needs 1.2 V on its core before it can talk on the bus depends on those pins being right, and a board with them tied to the wrong levels comes up at a voltage the processor will not accept. Some boards read this as a dead PMIC when it is a strap problem.
Dynamic voltage scaling is the reason for the I2C interface. The core converter can be moved between voltages while running, which is how a processor drops to a lower frequency and a lower core voltage to save power. The ramp is controlled by the part and the slew rate is specified, so the processor does not see a step. A board that does not use DVS is paying for an interface it does not need, and a simpler PMIC would do.
The 1.7 A core rating is a peak for a processor in burst. A processor that idles at 50 mA and bursts to 1.5 A needs a converter that recovers from the step without dropping below the minimum, and the output capacitor is what carries the load during the loop response time. The rating alone does not tell a customer whether the rail holds; the transient specification with the recommended capacitor does.
Two hundred milliamps on the general purpose LDOs is enough for a peripheral and not for a radio. The LDOs can be fed from one of the converters or from the battery directly, and when they run from the battery at 4.2 V with a 1.8 V output the dissipation is 0.48 W at 200 mA. That is a thermal problem in a 5 mm body shared with three converters, so the input source for each LDO is a real engineering decision rather than a convenience.
A 30 mA always-on regulator is what keeps the clock running. That rail stays alive when the rest of the system is off, and it is the one a battery backup connects to. Its quiescent current, not its load current, sets the shelf life of the product, and it is the reason the RTC rail is separate from the general purpose LDOs.
The reset delay is adjustable because processors differ. An external capacitor sets how long reset is held after the rails are valid, and the processor data sheet gives a minimum. A board that copies the capacitor from another board can release reset before the clock is stable, which produces a product that fails to start one time in twenty.
Forty pins in a 5 mm body need a ground plane and careful decoupling. Three converters switching in one package mean the input capacitor placement decides whether the rail noise stays inside the emission limit. Each converter needs its own input capacitor close to its pins, and the ground return for the small signal pins has to be separate from the power return, which is what the exposed pad is for.
The published reel is 250 pieces, not 3000. The orderable addendum for this string shows a small reel, which matters for a production line that expects a full reel and for a distributor quoting a quantity. Confirm the packing before the order rather than after, because a 250 piece reel does not cover a 1000 piece build.
What to confirm before this part goes on a purchase order
State the processor and its rail requirements. The default strap settings and the converter currents are chosen against a specific processor family, and a PMIC quoted without them cannot be checked.
Say whether DVS and the I2C interface are used. A board that only needs fixed rails can use a simpler part, and a board that needs DVS cannot use a part without the interface.
Where this order code fits
It powers a processor, its memory and its peripherals in a handheld instrument or an industrial panel PC, with a defined start order and dynamic core voltage control. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can the outputs be changed without I2C? Yes, within the sets the DEFDCDC and DEFLDO pins select. Each converter has a small number of predefined voltages plus an adjustable option, and the strap pins choose between them at start up. Anything outside those sets needs I2C traffic after the bus is alive.
Does it include a battery charger? No. This is a rail generator for a processor system, not a charger. A product with a battery needs a charger in front of it, and the PMIC then runs from the battery or from the system rail the charger produces.
What is the difference between the base part and the B revision? The default configuration. The silicon family and the pin out are the same and the B revision ships with different default voltages and enable behaviour. A board built for one and populated with the other can come up at the wrong rail voltage, which is a substitution that has to be checked against the strap table.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.