Contact Us

TPS63811YFFR

Brand: Texas Instruments
Texas Instruments TPS63811YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63811YFFR — Power Management & Signal Chain | Superb Automation

TPS63811YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63811YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63811YFFR 2.5 A buck-boost with an I2C interface

The TPS63811YFFR is the programmable member of the TPS63810 and TPS63811 pair: a 2.5 A non inverting buck-boost converter that runs from 2.2 V to 5.5 V, holds an output between 1.8 V and 5.2 V, and takes its output voltage from two registers written over I2C. The TPS63810 is the same silicon with the output presets fixed at 3.3 V and 3.45 V. Both parts sit in a 15 ball DSBGA of 2.3 mm by 1.4 mm and need four external components, which the vendor puts at under 20 square millimetres of solution area.

The two registers hold the output voltage in 25 mV steps above a 1.8 V base, and a range bit selects the upper half of the span, so the same part covers a 1.8 V core rail and a 5 V peripheral rail without a divider change. A VSEL pin decides which of the two registers is active, which is how a processor asks for a sleep voltage and a run voltage without a bus transaction. Writes during operation are followed by a programmable ramp rather than a step, so a rail that is already loaded does not see a jump.

Current delivery is 2.5 A at a 2.5 V input for a 3.3 V output, and 2.5 A at 2.8 V input for a 3.5 V output. Quiescent current is 13 microamps, and the shutdown current through the ENABLE bit is 0.35 microamps, so the part is usable in a product that keeps its converter off for most of its life.

Key parameters from the SLVSEK4C document

Input range2.2 V to 5.5 V, 6 V absolute maximum on the supply pins
Output range1.8 V to 5.2 V, set in 25 mV steps from the 1.8 V base with a range bit
Output current2.5 A at VIN 2.5 V and VOUT 3.3 V, 2.5 A at VIN 2.8 V and VOUT 3.5 V
InterfaceI2C slave with two output voltage registers, VSEL pin selects the active one
Quiescent current13 microamps into VIN with the enable high and no load
Shutdown current0.35 microamps with the ENABLE bit cleared
Mode controlAutomatic power save or forced PWM, both set over the bus
ProtectionOvervoltage on the output, overtemperature at about 130 degrees, forward and backward current limit
Start-upIntegrated soft start, starts into a pre-biased output, true load disconnect in shutdown
PackageYFF 15 ball DSBGA of 2.3 mm by 1.4 mm, moisture level 1, minus 40 to 125 degrees

What the I2C control is good for

Dynamic voltage scaling is the obvious use: a processor that drops from 3.3 V to 1.8 V in sleep saves far more than the converter's own quiescent current, and the ramp makes the transition safe with the load still attached. The second use is a production line that builds one board for several product variants and sets the rail in the test fixture instead of stocking several converters.

The TPS63811 has to be programmed before start-up if the rail must come up at a voltage other than its default, because the registers load at power on. The TPS63810 avoids that step by shipping with its two presets already in place, which is the reason a product that never changes its rail in the field usually takes the fixed member and skips the bus entirely.

Where this part fits

System pre regulators in phones, tablets, tracking units, point of sale terminals and true wireless earphones, point of load rails for camera sensors and cable adapters, thermoelectric and optical module supplies, and radio or SoC rails that have to follow a load profile. Cross references for the family sit under power management cross reference and the replacement route under pin to pin cross reference.

What to check before a purchase order

Check which of the two parts the board was released against. TPS63810YFFR and TPS63811YFFR are both 3000 pieces on a large reel, both moisture level 1, both in the same 15 ball body, and both active. The only difference is whether the output presets are programmed in the factory, so a reel swapped between them produces a board that boots at the wrong voltage or ignores the bus.

Check the pull ups on SDA and SCL against the bus voltage, and check that the master issues a stop condition after the first power up, because the vendor calls that out explicitly for correct reset of the interface. The incoming check for programmable parts is in incoming inspection plan.

Questions that come up on this part

What happens if the bus is silent? The part runs at the voltage in the register selected by VSEL, which on a fresh part is the factory value, so a host that never writes the bus is not a failure, it is simply a fixed rail.

Can the output be changed while the load is active? Yes, and the ramp rate is programmable, but the load current has to stay inside the current limit through the transition, which means a step from 1.8 V to 3.3 V under full load can trip the limit if the ramp is set too fast.