Contact Us

TPS63806YFFR

Brand: Texas Instruments
Texas Instruments TPS63806YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63806YFFR — Power Management & Signal Chain | Superb Automation

TPS63806YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63806YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63806YFFR 2 A buck-boost tuned for load steps

The TPS63806YFFR is the load step member of the TPS6380x family. It regulates 2 A at a 3.3 V output from a 2.3 V input, tolerates 2.5 A transients, and the vendor quotes 180 mV of output deviation for a 2 A load step. That figure is the reason to pick this member over its two siblings when the load is a time of flight camera sensor, a radio front end that keys on and off, or a thermoelectric driver that changes current in milliseconds.

Electrically the part sits on the same silicon and the same 15 ball WCSP of 2.3 mm by 1.4 mm as the rest of the family, with a 1.3 V to 5.5 V input and a 1.8 V to 5.2 V adjustable output. What differs is the loop compensation and the peak current limit. The TPS63806 limits the peak inductor current at 5.5 A at a 2.5 V input, against 5 A on the other two members, and it draws 13 microamps of quiescent current instead of 11 microamps.

That trade is worth stating plainly at the purchasing desk: two microamps of standby current buy roughly a third of the transient headroom. A product that sleeps for years on a coin cell takes the TPS63805. A product that wakes a camera or a transmitter several times a minute takes the TPS63806 and pays the two microamps.

Key parameters from the SLVSDS9E document

Input range1.3 V to 5.5 V operating, start-up above 1.8 V
Output range1.8 V to 5.2 V adjustable
Output current2 A at VIN 2.3 V and VOUT 3.3 V, 2.5 A transient, 180 mV for a 2 A step
Quiescent current13 microamps into VIN with the enable high and no load
Shutdown current45 nA typical and 600 nA maximum into VIN, 0.5 nA typical into VOUT
Peak current limit5.5 A at VIN 2.5 V against 5 A on the TPS63805 and TPS63807
Switch resistance47 and 30 milliohm on one leg, 43 and 18 milliohm on the other, at 3 V input
Switching frequency1.4 MHz near unity ratio, rising to 2.1 MHz at 2.3 V input
Mode controlMODE pin selects power save or forced PWM, power good on an open drain output
Soft start480 microsecond ramp for low inrush, 224 microsecond linear ramp on the current limit
PackageYFF 15 ball WCSP of 2.3 mm by 1.4 mm, moisture level 1, minus 40 to 125 degrees

How the load step number is reached

180 mV at a 2 A step on a 3.3 V rail is about 5.5 per cent deviation, which is inside the tolerance of most 3.3 V logic and well inside the tolerance of an analogue rail that feeds an LDO afterwards. It is reached because the inductor is small, the loop is fast, and the converter is allowed to run in forced PWM when the load is present. In power save mode at light load the same part skips pulses, the ripple rises and the response to a step slows, so a product that needs the 180 mV figure has to hold the MODE pin high.

That detail is the one most often missed in a first prototype. The pin is a logic input, not a strap option, and the vendor provides it precisely because the two behaviours cannot both be optimal.

Where this part fits

Time of flight camera modules, broadband radio and SoC supplies in IoT and tracking products, thermoelectric cooler drivers and optical module supplies, plus general purpose rails that sit between a battery and a 3.3 V load. The same family covers the plain low current case, which our sourcing desk tracks under power management cross reference and one stop BOM sourcing.

What to check before a purchase order

Check that the reel carries TPS63806YFFR and not one of its two siblings. All three are active, all three are 3000 pieces on a large reel, all three are the same 15 ball body with the same SNAGCU finish and moisture level 1, and all three are rated minus 40 to 125 degrees. Nothing on the reel except the marking distinguishes them, so the label has to be read rather than assumed. The 250 piece small reel row is TPS63805YFFT, which is a different part entirely.

Check the output capacitor against the 22 microfarad minimum the vendor specifies, and check the inductor against the 5.5 A peak limit. An inductor chosen for the 2 A average will be the first part to fail a transient test. The reel level check we run is described in date code management.

Questions that come up on this part

Is the 2.5 A transient figure a continuous rating? No. It is the short term current the loop can deliver before the peak limit folds back, and the continuous rating stays 2 A at 2.3 V input, less at lower input voltage because the input current limit binds.

Can two of these be paralleled for 4 A? Not safely. There is no current share pin and no droop sharing specification, so two converters on one rail will fight at the point where their references differ by a few millivolts.