Contact Us

TPS63070RNMR

Brand: Texas Instruments
Texas Instruments TPS63070RNMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63070RNMR — Power Management & Signal Chain | Superb Automation

TPS63070RNMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63070RNMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63070RNMR: 2 V to 16 V buck-boost converter with 3.6 A switch current in a 2.5 mm by 3 mm QFN

TPS63070RNMR is a four switch buck-boost converter that holds its output whether the input sits above, below or equal to it in a VQFN body of 15 pins. It replaces the two stage arrangement of a boost followed by a buck on rails that move, and it keeps a 5 V output alive from a two cell lithium pack that falls from 8.4 V to 6 V and from a 12 V adapter that droops.

Order code and package

Order codeTPS63070RNMR, RNR package, VQFN 2.5 mm by 3 mm, 15 pins including the thermal pad
Family membersTPS63070 adjustable with output discharge off, TPS630701 fixed 5 V, TPS630702 adjustable with a 200 ohm discharge switch
BodyVQFN, 2.5 mm by 3 mm, 0.9 mm tall, exposed thermal pad on the underside
InductorOne inductor between L1 and L2, the four switches are all inside the package
Feedback0.8 V reference on the adjustable parts, 1.5 Mohm divider impedance on the fixed 5 V part
Output range2.5 V to 9 V adjustable, 5.0 V fixed on the TPS630701

Electrical parameters that decide the application

Input range2.0 V to 16 V operating, 20 V absolute maximum on VIN, EN, PS/SYNC and VSEL
Output current2 A in buck mode and 2 A in boost mode, quoted at VIN 4 V and VOUT 5 V
Switch current3.6 A typical switch current limit, which is what actually bounds the load at low input
Input current limit3.05 A to 4.15 A positive average input current, 1.1 A to 1.8 A negative, measured at VIN 5 V and VOUT 6.5 V
Switching frequency2.4 MHz typical, 2.1 MHz to 2.7 MHz across the range, synchronisable from 2.1 MHz to 2.8 MHz
Feedback accuracyminus 1 per cent to plus 1 per cent in forced PWM, minus 1 per cent to plus 3 per cent in power save mode
Switch resistancebuck high side 50 mOhm typical and 80 mOhm maximum, buck low side 70 mOhm, boost high side 40 mOhm, boost low side 80 mOhm at 5 V
Quiescent current50 uA typical with the output in regulation and no load, power save mode enabled
Under voltage lockout1.85 V typical rising, 1.7 V to 1.95 V across parts, with 525 mV to 850 mV of hysteresis
Start-up70 us delay from the enable pin, then 400 us from 5 per cent to 95 per cent in buck mode and 850 us in boost mode
Output discharge200 ohm switch to ground, TPS630702 only

Family variants and how they differ

TPS630701the same die with a fixed 5 V output and no discharge switch, so the feedback pin becomes an output sense point and the divider is internal
TPS630702adjustable like the TPS63070 but with the 200 ohm output discharge switch, which is the part to specify when the rail has to be pulled down at power off
TPS55288a four switch buck-boost for higher power, 16 A inductor current limit and 6.35 A output limit, in a larger body with an I2C interface
TPS63802 and TPS63810later single inductor buck-boost families in the same 2.5 mm by 3 mm class, with lower input range and different control
A boost followed by a bucktwo converters and two inductors, which is the arrangement this part is bought to replace, at the cost of the cascade efficiency

Points to check before this part goes on a BOM

The 2 A figure is quoted at VIN 4 V and VOUT 5 V, which is a boost ratio of 1.25 and a comfortable point for the part. Move the input down and the same 2 A output stops being available, because the switch current and the average input current limit bind first. At 3 V in and 5 V out with 90 per cent efficiency the input current is 3.7 A, above the 3.05 A minimum positive input current limit, so a board that needs 2 A at 3 V in is outside the part and the data sheet figure should not be read as a flat rating.

The negative input current limit of 1.1 A to 1.8 A is the number that decides what happens when the output is pre-biased or when the load pushes current back. A 5 V rail held up by a second source while this converter is enabled will see the part sink current until that limit, and the inductor and the input capacitor have to carry it. Boards that stack two supplies on one rail without a diode need to check this row rather than assume the converter only sources.

Power save mode and forced PWM are not just an efficiency choice, they change the accuracy specification. In forced PWM the feedback window is minus 1 per cent to plus 1 per cent, and in power save mode it widens to minus 1 per cent to plus 3 per cent because the part stops switching between bursts and the output is allowed to ride up. A rail that feeds an ADC reference or a radio has to stay in forced PWM, and the price is quiescent current in the milliampere range instead of microamps.

The PS/SYNC pin carries three functions: pull it low for forced PWM, pull it high for power save, or drive it with a clock between 2.1 MHz and 2.8 MHz to lock the switching frequency to a system clock. That last option is the one that keeps the converter out of a radio band, and it also removes the beat between two converters on the same board. A board that leaves the pin floating has no defined mode, so the pin belongs on a resistor to either rail.

The VSEL pin gives a two level output without a second divider. When VSEL goes high the part switches in an internal 25 ohm to 100 ohm resistor from FB2 to ground, which changes the divider ratio and moves the output to the higher of the two settings. FB2 leakage is 100 nA, and that leakage flows through the divider, so a 1 Mohm divider built for a 10 uA budget has its ratio moved by a tenth of a per cent. The resistor is specified with a 4 to 1 window, so the two output levels are not exact ratios of each other and both have to be trimmed against the 0.8 V reference individually.

The output discharge switch belongs to the TPS630702 only. On the other two parts the output falls at whatever rate the load and the output capacitor set, which on a light load can be seconds. A board that sequences a second rail off this one, or that has to guarantee a rail is down before a connector is exposed, needs the discharge part; a board that only needs the rail to stop delivering can use the TPS63070 and save the extra order code.

The start-up ramp is fixed at 400 us in buck mode and 850 us in boost mode, measured from 5 per cent to 95 per cent. Inrush into the output bank is therefore set by the capacitor value: 100 uF charged in 400 us is 0.25 A of average charging current on top of the load, which is inside the switch limit, but 470 uF pushes it to 1.2 A and starts to compete with the current limit at the same time as the load comes on. The data sheet numbers are for a 3.3 V output at 500 mA in buck and 250 mA in boost, so a heavier load lengthens the ramp.

The under voltage lockout at 1.85 V with 525 mV to 850 mV of hysteresis is what makes the part usable from a two cell pack. A converter that trips at 1.85 V and only releases at about 1.0 V will not chatter on a source with hundreds of millivolts of sag, which is the normal condition when a transmitter keys on a battery rail. The other side of the same row is that the part keeps running down to 2.0 V, so a pack discharged below that point is being asked for current it cannot give, and the input capacitor has to supply the difference for the length of each switching cycle.

In buck mode the output is limited to about 0.3 V below the input when the input is under 6 V. That rules out a 3.3 V rail from a 3.6 V source with any margin at all, and it rules out passing a 5 V rail through to a 5 V load. The part regulates across the transition, but the useful headroom starts at roughly 300 mV and the efficiency curve is at its worst exactly at the crossover, because the inductor current ripple and the switch losses are highest when the duty is near 50 per cent.

Where this order code fits

It belongs on a rail that is fed from a battery or an adapter whose voltage crosses the load voltage: a two cell lithium instrument that has to hold 5 V from 8.4 V down to 6 V, a 12 V industrial board that has to hold 9 V through a brownout, or a handheld meter that runs from a 5 V USB input and a 3.7 V cell on the same node. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can it deliver 2 A from a 3 V input at 5 V out? No. The 2 A rating is quoted at 4 V in and 5 V out. At 3 V in the average input current for 2 A out is about 3.7 A, above the 3.05 A minimum positive limit, so the part limits before the load is reached.

What is the difference between the TPS63070 and the TPS630702? The 702 adds a 200 ohm switch that discharges the output when the part is disabled. The adjustable output and the 3.6 A switch current are the same, so the choice is about power-down behaviour, not performance.

Does the output stay accurate in power save mode? It stays inside minus 1 per cent to plus 3 per cent, against minus 1 per cent to plus 1 per cent in forced PWM. A rail that has to hold a tight window needs the PS/SYNC pin pulled low.

Can two output voltages be selected at run time? Yes, with the VSEL pin and one resistor from FB to FB2. The internal FB2 resistance is specified over a 4 to 1 window, so both levels have to be trimmed against the 0.8 V reference rather than computed from a nominal ratio.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.