Contact Us

TPS63051RMWR

Brand: Texas Instruments
Texas Instruments TPS63051RMWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63051RMWR — Power Management & Signal Chain | Superb Automation

TPS63051RMWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63051RMWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63051RMWR: single inductor buck-boost converter with 1 A switches and a fixed 3.3 V output

TPS63051RMWR is a buck-boost converter that holds 3.3 V from an input that swings above and below the output in a VQFN (HotRod, RMW) body of 12 pins. It takes 2.5 V to 5.5 V in, holds 3.3 V at 500 mA in boost and 1 A in buck, switches at 2.5 MHz and draws 43 uA of quiescent current, so a single cell product keeps regulation through the whole discharge curve instead of dropping out halfway down it.

Order code and package

Ordering stringTPS63051RMWR, the fixed 3.3 V member of the TPS6305x family in the 12 pin HotRod VQFN
Body2.50 mm by 2.50 mm VQFN with the inductor pads on the top side of the package, which keeps the switching loop short
Second body in the family12 pin DSBGA, 1.56 mm by 1.16 mm, used on the TPS63050 and on the same silicon as this part
Output settingFixed at 3.3 V inside the chip, so no feedback divider is needed and no divider current is wasted at light load
Input range2.5 V to 5.5 V, with the full 500 mA output guaranteed from 2.5 V in
Switch rating1 A average current in the switches, which is why the output current falls in boost mode and rises in buck mode
Shutdown behaviourThe load is disconnected from the battery when the device is off, so a sleeping product does not drain through the output rail

Electrical parameters that decide the application

Output current in buck mode1 A continuous with the input above the output, limited by the switch current rather than by the die
Output current in boost mode500 mA continuous into 3.3 V from 2.5 V in, the figure the front page quotes
Quiescent current43 uA typical with no load and the output in regulation at 3.6 V in, 65 uA maximum after revision D raised the ceiling from 60 uA
Shutdown current0.1 uA typical, 1 uA maximum, with the output disconnected
Switching frequency2.5 MHz typical, fixed, which keeps the inductor at 1.5 uH and the output capacitor at 10 uF
Undervoltage lockout1.7 V typical on a falling input, 1.6 V minimum, 1.8 V maximum, with 200 mV of hysteresis
Thermal shutdown140 degrees rising, 20 degrees of hysteresis, restarting without a latch
Output accuracyplus or minus 1.1 per cent in forced PWM at 25 degrees, plus or minus 3 per cent over the full temperature range
Switch resistance145 milliohm on the input high side FET, 95 milliohm on the output high side, 170 on the input low side and 115 on the output low side, all measured at 500 mA of switch current
Input current limit1.24 A, 1.4 A and 1.95 A typical for the three ILIM pin combinations, set in hardware rather than by a resistor
Soft start280 us in buck mode and 600 us in boost mode with the SS pin floating, extended by a capacitor when the load cannot take the inrush
Start up delay100 us from the enable pin going high to the first switching cycle
Power goodOpen drain output, 0.3 V low level at 100 uA of sink, usable as a reset to a downstream 3.3 V device
Logic thresholds1.2 V minimum for a high on EN, ILIM0 and ILIM1, so a 1.8 V GPIO drives the part directly

Family variants and how they differ

TPS63050The adjustable member. Same silicon, same packages, but the output is set by an external divider into a 0.8 V reference, and the feedback pin draws 10 nA of bias current
TPS63051The fixed 3.3 V member on this page. No divider, no divider drift, and the output tolerance is quoted against the internal reference
Power save modeThe PFM/PWM pin chooses between automatic power save at light load and forced PWM at a fixed 2.5 MHz. Power save buys efficiency below a few milliamps and costs output ripple
Load disconnectBoth members disconnect the load in shutdown, which matters when the battery stays connected to the board for months
ILIM pinsTwo pins give four input current limit settings, so the same part can serve a 500 mAh cell and a 2 A hour pack without a component change
Package choiceThe DSBGA body is smaller, the HotRod QFN is easier to inspect and rework and has the better thermal path to the board

Points to check before this part goes on a BOM

The 500 mA headline belongs to boost mode from 2.5 V in. In buck mode the part carries 1 A, so a 3.3 V rail at 800 mA from a 5 V input is inside the rating while the same 800 mA from 2.5 V is not.

Quiescent current rose from 60 uA to 65 uA maximum in revision D. A specification copied from an older data sheet will be optimistic by 5 uA, which matters on a coin cell product but not on a mains powered one.

The input current limit is set by two digital pins, not by a resistor, and the three published settings are 1.24 A, 1.4 A and 1.95 A typical. A board that needs 1.1 A from a weak cell should take the lowest setting and accept the reduced output current rather than raise the limit.

Soft start time is quoted with the SS pin open. With a capacitor fitted the ramp stretches, and on a boost start into a heavy capacitive load the inductor current reaches the limit before the output arrives unless the ramp is slowed.

The mode crossover has no dead band by construction, but the output can show a small step if the input crosses the output slowly with a light load and power save enabled. Forcing PWM removes the step and costs light load efficiency.

The package is a 2.5 mm square QFN with the inductor pads on top. Reflow profile and stencil aperture for those pads follow the package drawing, and hand rework of the inductor is practical where a DSBGA would need a reball.

What a buck-boost does that a buck cannot

A single lithium cell runs from 4.2 V down to 3.0 V, and a 3.3 V rail sits inside that window. A buck converter drops out when the cell reaches about 3.5 V and the product loses regulation for the second half of the discharge. A boost converter cannot start until the cell is above the output. The buck-boost switches between the two modes on the fly, so the rail holds 3.3 V from 2.5 V to 5.5 V in, which is the reason this family exists.

The price of that range is efficiency and parts count. One inductor, one 10 uF input capacitor and one 10 uF output capacitor cover the whole converter, and the switches are inside the package. Nothing external sets the transition point, so there is no resistor to drift and no factory trim to lose.

Where this order code fits

Battery powered equipment that runs from one lithium cell or a two cell pack is the natural home for this part: the pack voltage crosses 3.3 V during normal discharge, so a plain buck or a plain boost leaves a dead band in the middle of the discharge curve. Handheld instruments, meters, portable medical monitors and 3.3 V radio modules fed from a single cell all sit in that band. The converter switches between modes on its own, and the crossover is where most competing parts show a glitch in the output. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can this part run from a 5 V rail and deliver 3.3 V at 1 A? Yes, in buck mode. The switch current limit and the 1 A average switch rating set the ceiling, and 1 A at 3.3 V from 5 V leaves margin. The 500 mA figure applies to the boost side only.

What happens between 3.2 V and 3.4 V in, where the input is close to the output? The part runs through the transition with the switches in a mixed state and holds regulation. Expect efficiency in the high 80s in that band, which is the lowest point of the curve, and check the ripple there if the load is sensitive.

Is the 3.3 V output accurate enough for a radio? Plus or minus 3 per cent over temperature in power save mode and plus or minus 1.1 per cent in forced PWM at room temperature. Most 3.3 V radio front ends accept 3 per cent; a part that needs 1 per cent over temperature should use the adjustable member with a 0.1 per cent divider.

Does it need an external Schottky diode? No. Both rectifiers are inside the package. Adding a diode in parallel gains nothing and adds leakage.

How is the part turned off cleanly? Pull EN low. The output is disconnected from the input, the quiescent current falls to 0.1 uA, and the output decays through the load rather than through the chip.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.