Contact Us

TPS63050YFFR

Brand: Texas Instruments
Texas Instruments TPS63050YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63050YFFR — Power Management & Signal Chain | Superb Automation

TPS63050YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63050YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63050YFFR 500 mA buck boost with adjustable soft start

The TPS63050YFFR is a four switch single inductor buck boost converter with 1 A switches that delivers 500 mA in boost and up to 1 A in buck, from an input between 2.5 V and 5.5 V. It switches at 2.5 MHz, keeps its quiescent current below 60 microamp, and reaches above 90 per cent efficiency in boost and above 95 per cent in buck. The body is the YFF WCSP of twelve bumps, and the same document covers the RMW HotRod body of twelve pins.

What separates this member from the rest of the buck boost line is the adjustable soft start and the programmable inrush limit. The SS pin takes a capacitor that sets the ramp, and the ILIM0 and ILIM1 pins select an inrush current level, which lets a board start into a large output capacitance without pulling the input rail down. The power good output is open drain and can drive a sequence gate directly, so a multi rail product can order its power up without a sequencer.

The ILIM1 pin is available on the DSBGA body only, and on the VQFN body it is tied internally above the high threshold, which means the two bodies do not offer the same set of inrush levels even though they are the same converter. That detail is worth knowing before a bill of materials is frozen, because a board that relies on a low inrush setting cannot simply be moved to the other package.

Key parameters from the SLVSAM8D document

Input range2.5 V to 5.5 V
OutputAdjustable on this member, 3.3 V fixed on the TPS63051
Output current500 mA in boost and up to 1 A in buck
Switch current limit1 A typical average current in the switches
Switching frequency2.5 MHz typical
EfficiencyAbove 90 per cent in boost and above 95 per cent in buck
Quiescent current43 microamp typical and 65 microamp maximum on the input supply
Soft startAdjustable with a capacitor on the SS pin
Inrush limitProgrammable through ILIM0 and ILIM1, with ILIM1 available on the DSBGA body only
Power goodOpen drain output referenced to the output level
Mode pinPFM and PWM selection for light load behaviour
PackagesYFF WCSP of twelve bumps and RMW HotRod of twelve pins, both 1.6 mm by 1.2 mm class

Why the ramp and the inrush limit are the useful pins

A buck boost converter starting into a discharged output capacitor draws its current limit until the output reaches regulation. On a product where the same battery also feeds a radio that is in the middle of a transmission, that inrush is a supply glitch, and the radio sees a droop that looks like a brownout. Setting the inrush limit below the battery capability and the ramp long enough to stay out of the radio window removes the interaction, and both are pin settings rather than external components.

The power good output is the other half of the same problem. A rail that is still ramping must not enable the next stage, and a rail that has collapsed must disable it before the load discharges the capacitor further. On a board with a 3.3 V rail feeding a 1.8 V rail, the power good of the first converter is the enable of the second, and the ramp of the first decides the timing of the whole sequence.

The quiescent current of 43 microamp typical is a reminder that this part is for a working product rather than for a sleeping one. A product that idles between transmissions should use the PFM mode to reduce the switching activity, and a product that is asleep for hours should be looking at a converter with a nanoamp quiescent current rather than at this one.

Where this part fits

Portable instruments with a 3.3 V rail, wireless terminals that transmit in bursts, medical monitors with a sequenced power up and any single cell product where the inrush has to be controlled. Our cross reference notes are at power management cross reference and the drop in check is at how to verify a drop in replacement.

What to check before a purchase order

Check the package against the inrush requirement. ILIM1 is available on the DSBGA body and tied high internally on the VQFN body, so a board that depends on the low inrush setting cannot be built in the second package. The order code carries the body, and the packing label is where to confirm it.

Check the soft start capacitor and the inductor together. A long ramp into a large output capacitor charges the inductor current slowly, which is safe, but it also keeps the converter in its start up state for longer, and a product that expects to be ready in a few milliseconds has to account for the ramp. The receipt check we run is at incoming inspection plan.

Questions that come up on this part

Can the part be used at 5 V output from a 3.7 V cell, is a common question. It can, and the boost mode covers it, but the available output current falls as the ratio rises, so a 500 mA load at 5 V from 3 V input is at the edge of the switch limit rather than comfortably inside it. The curves in the document give the number for a specific input and output pair.

The second question is whether the power good output can be tied to the enable of the next rail directly. It can, because it is an open drain output that can sink the enable current of a following converter, provided the pull up is on the correct rail. A pull up on a rail that is not yet alive leaves the signal undefined, which is the fault that sequencing is supposed to prevent.