Contact Us

TPS63036YFGR

Brand: Texas Instruments
Texas Instruments TPS63036YFGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63036YFGR — Power Management & Signal Chain | Superb Automation

TPS63036YFGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63036YFGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63036YFGR: a 1 A switch buck boost converter in a 1.8 mm by 1.1 mm wafer scale package

TPS63036YFGR is a non inverting buck boost converter that keeps a regulated output from an input that is above, below or equal to it, in a package small enough for a headset or a sensor node in a WCSP body of 8 pins. The switch current is limited to 1 A typical, which sets the load the part can carry at a given input and output rather than a fixed current rating.

Order code and package

Catalogue stringTPS63036YFGR, the only order code in the addendum for this body
BodyYFG, WCSP, 8 pins, 1.814 mm by 1.076 mm, junction to ambient 84 C per watt
Reel3000 pieces on a large tape and reel
Finish and moistureSNAGCU plating, moisture level 1, 260 C, unlimited floor life
Temperatureminus 40 to 125 C
MarkingS63036, printed on a body this small
DocumentSLVSB76B, revised August 2019

Electrical parameters that decide the application

Input range1.8 V to 5.5 V, with more than 2 V needed for start-up
Output range1.2 V to 5.5 V, set by an external divider on FB
Reference495 mV to 505 mV around a 500 mV nominal, the window that sets the output tolerance
Switching frequencyfixed 2.4 MHz, and the part can be synchronised to an external clock
Switch current limit1000 mA typical average current in the switches, which is the real limit on load current
Quiescent current25 uA typical operating, 35 uA maximum
Shutdown current0.1 uA typical, 0.9 uA maximum
Undervoltage lockout1.6 V to 2.0 V rising, 1.4 V to 1.6 V falling
Enable thresholds1.2 V high, 0.4 V low, with 0.1 uA of pin current
Thermal shutdown140 C
Shutdown behaviourthe load is disconnected from the supply, so a depleted cell cannot discharge through the converter
Protectionovertemperature and overvoltage protection, both integrated

Where this member sits in the family

TPS63036YFGRthe 1 A switch member in the 1.814 mm by 1.076 mm body, the part on this page
Other membersthe family carries versions with a higher switch limit and fixed output options, which is where to look when 1 A of switch current is not enough
Divider based outputno fixed output version is listed in this revision, so every board carries a divider
Package markingS63036, four digits and a letter laser marked on a body smaller than a grain of rice
Power save controlthe PS/SYNC pin either enables power save, disables it, or takes an external clock, all on one pin
Synchronisationan external clock is applied to the same pin and the converter follows it, which is how the switching tone is moved out of a radio band
Inductor1.5 uH is the value the typical application uses, and the switch current limit is what sets the saturation current the inductor has to survive

Points to check before this part goes on a BOM

A 1 A switch limit is not a 1 A output rating. The load the part can carry depends on the input and output ratio, because in boost mode the input current is larger than the output current by roughly that ratio. A 3.3 V output from a 1.8 V input can support a much smaller load than the same output from a 4.2 V cell.

Start-up needs more than 2 V even though operation continues down to 1.8 V. That distinction matters on a two cell alkaline product, where the converter starts on fresh cells and keeps running as they fall, but does not restart if the product is switched on with nearly flat cells.

The 500 mV reference is low, which is what allows a 1.2 V output from the same divider that produces 5 V. It also means the divider current is a real part of the standby budget on a 25 uA converter, and a divider drawing 5 uA is a fifth of the total.

Load disconnect in shutdown is the feature that decides whether a product can sit in a drawer. Without it the inductor and the body diode of the high side switch form a path from the cell to the load, and a sleeping product drains through its own converter.

Moisture level 1 with unlimited floor life is not a small thing on a wafer scale body. It means the reel does not have to be baked after a weekend out of the dry cabinet, which on a part this small is the difference between a usable line and a stopped one.

Fixed 2.4 MHz keeps the inductor small, and synchronisation keeps the switching tone out of a radio band. On a headset or a sensor node with a 2.4 GHz radio, the ability to move the clock is worth more than the few per cent of efficiency that a lower frequency would bring.

Working out the load a 1 A switch will carry

In boost mode the switch carries the input current, so the output current is the switch limit multiplied by the input voltage and divided by the output voltage, less the losses. A 3.3 V output from a 1.8 V input therefore supports roughly half of what the same part supports from a 3.6 V input.

In buck mode the switch carries the output side current and the same 1 A applies with much less derating. A product that runs from a cell across 3.0 V to 4.2 V and needs 3.3 V spends most of its life near the crossover, which is the worst case for a buck boost and the case worth measuring on the bench.

Why the reference is 500 mV

A low reference lets one divider cover 1.2 V to 5.5 V without the resistor values becoming impractical at the top end. It also makes the feedback pin sensitive to noise, because 500 mV of signal is small next to the switching node a few millimetres away.

The practical consequence is that the divider should sit close to the pin with a short return, and that the FB trace should not run under the inductor. The vendor's evaluation board shows the arrangement that works.

Where this order code fits

This is the converter in a headset, an earbud case, a camera module or a wireless sensor, where the cell voltage crosses the rail voltage during discharge and the product has to keep working on both sides of that crossing. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can it deliver 1 A at the output? Only in buck mode with a high enough input. The 1000 mA figure is the average switch current, and in boost mode the output current is lower than the switch current by the voltage ratio.

What happens below 2 V at start-up? The part does not start. Operation continues down to 1.8 V once running, so a product switched on with nearly flat cells may not come up even though a running product would keep going.

Is an external clock required? No. The PS/SYNC pin has an internal 2.4 MHz oscillator and can be tied high or low to select power save or forced continuous operation. A clock is only needed when the switching tone has to be moved.

What sets the output voltage? A divider from the output to FB to ground against 500 mV. The window is 495 mV to 505 mV, so one per cent of the output tolerance is the reference itself.

Does the load stay connected in shutdown? No, it is disconnected. That is the behaviour to want on a battery product, because the converter then adds nothing to the shelf drain.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.