TPS63030DSKR
Product Specifications
TPS63030DSKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS63030DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS63030DSKR: adjustable buck boost with 1 A switches and a 2.5 mm by 2.5 mm body
TPS63030DSKR is a single inductor buck boost converter that keeps an adjustable rail in regulation while a two or three cell alkaline pack or a single lithium cell moves above and below it in a VSON body of 10 pins. It takes 1.8 V to 5.5 V in, sets any output between 1.2 V and 5.5 V from a 500 mV reference, and moves between step down and step up without a mode command. The average switch current limit is 1 A typical with a 900 mA floor and a 1.3 A ceiling, which the document turns into 800 mA of output at 3.3 V from an input above 3.6 V and 500 mA in boost from an input above 2.4 V.
Order code and package
| TPS63030DSKR | 10 pin VSON (DSK), 2.50 mm by 2.50 mm, 3000 pieces on a large reel, nickel palladium gold or tin finish depending on the row, moisture level 1 unlimited, marking CEF, minus 40 C to plus 125 C |
| TPS63030DSKT | same body, 250 pieces on a small reel |
| TPS63031DSKR | the fixed 3.3 V member on the same body, marking CEF, 3000 pieces on a large reel |
| Body | 10 pins with VIN, VINA, L1, L2, VOUT, FB, EN, PS/SYNC, GND and PGND, and the two inductor pins on opposite sides of the package |
| Second row per code | the addendum repeats each string with an .A suffix, and the finish column differs between the plain row and the .A row on this body |
Electrical parameters that decide the application
| Input voltage | 1.8 V to 5.5 V on both the power and the analogue supply pins, with a lockout between 1.4 V and 1.6 V when the input falls |
| Output voltage | 1.2 V to 5.5 V adjustable from the 500 mV reference, or fixed at 3.3 V on the TPS63031 |
| Output current | 800 mA at 3.3 V in step down from 3.6 V to 5.5 V of input, and up to 500 mA at 3.3 V in boost from an input above 2.4 V |
| Switch current limit | 900 mA minimum, 1000 mA typical and 1300 mA maximum, averaged over the switching cycle |
| Switching frequency | 2.5 MHz typical in fixed frequency operation, which sets the inductor to a 1.5 uH chip part |
| Quiescent current | 25 uA typical and 35 uA maximum with both supply pins at 3.6 V and no load |
| Shutdown current | 0.1 uA typical and 0.9 uA maximum, with the load disconnected from the input through the four switch topology |
| Power save mode | entered automatically at light load, and disabled by driving the PS/SYNC pin high to force fixed frequency operation |
| Synchronisation | the PS/SYNC pin also accepts an external clock, which moves the switching frequency to the applied rate |
| Protection | average current limit with a foldback to less than half the nominal value on a hard short, and thermal shutdown |
| Output capacitor | 10 uF ceramic on the output in the vendor circuit, with a second 10 uF on the input and a 0.1 uF on the analogue supply pin |
Adjustable or fixed, and which mode
| TPS63030 | adjustable from 1.2 V to 5.5 V with two resistors, and the only member of the pair that can build a rail other than 3.3 V |
| TPS63031 | fixed 3.3 V, same body, same reel, no divider and no feedback pin connection |
| PS/SYNC low | power save mode, where the converter skips cycles at light load and the quiescent current falls to the 25 uA figure |
| PS/SYNC high | fixed frequency operation at 2.5 MHz, which is the setting for a board that has to keep the switching tone out of a signal band |
| External clock | applied to the same pin, between the limits in the timing table, which lets several converters run at one rate |
| Load disconnect | built into the four switch topology, so the load is separated from the input in shutdown without an extra FET |
Points to check before this part goes on a BOM
The two output current figures answer different questions. 800 mA applies in step down with the input between 3.6 V and 5.5 V, which is the easy direction. 500 mA applies in boost with the input above 2.4 V, and it falls further as the input approaches the lockout at 1.5 V. A single cell product that quotes 800 mA from this part is quoting the wrong row, because a lithium cell spends most of its discharge below 3.6 V and the converter is in boost for all of it.
The average switch current limit is 1 A typical with a 900 mA floor. Because it is an average rather than a peak, the inductor sees a current that is already smoothed, and the ripple can sit on top of it without tripping the limit. That is why the vendor can quote 800 mA of output from a 1 A switch while a peak limited part of the same rating would deliver less. The floor of 900 mA is the number that has to cover the worst case build.
The switch from step down to boost is automatic and needs no mode pin. What the board does need is a tight inductor loop, because both switch pins carry the full current and any loop area between them and the input capacitor radiates. The vendor's own application circuit puts a 1.5 uH inductor directly across the two switch pins with a 10 uF input capacitor within a few millimetres. A board that routes those two traces across the board will pass bench tests and fail radiated emissions.
The quiescent current of 25 uA typical belongs to power save mode with no load. In forced fixed frequency operation the same part draws more, because the oscillator and the gate drivers keep running whether or not the load needs them. A board that sets PS/SYNC high for noise reasons gives up the light load efficiency and should check the standby budget against the fixed frequency figure rather than the power save one.
The shutdown current of 0.1 uA typical and 0.9 uA maximum includes the load disconnect, because the four switch topology opens the path from input to output when the enable pin goes low. That is what allows this part to sit on a battery without a series FET, and it is also why the output falls to zero rather than to a diode drop above ground. The 0.9 uA maximum is the number to use for shelf life, not the typical.
The foldback in the current limit is worth understanding before a short circuit test. On a hard short the limit drops to less than half of nominal and the switching frequency may fall as well, so the fault current is not a constant 1 A and the input supply sees a pulsing load rather than a steady one. A front end fuse sized from the nominal limit will be slow to open, and an upstream regulator with a tight current limit may see a load it cannot distinguish from a start up inrush.
The fixed 3.3 V member exists because most of these converters end up on a 3.3 V rail, and the divider is two resistors and a tolerance that a fixed part removes. The marking on both bodies is CEF, so a board that mixes the two strings cannot tell them apart by sight. A purchasing mistake that substitutes the fixed part for the adjustable one produces a 3.3 V rail where the divider expected something else, and the fault looks like a circuit error rather than a part number error.
Where this order code fits
It sits in blood glucose meters, portable data terminals, camera modules and any handheld product powered by two or three alkaline cells or one lithium cell whose voltage crosses the 3.3 V rail during discharge. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
How much output current in boost mode? Up to 500 mA at 3.3 V from an input above 2.4 V, falling as the input approaches the 1.5 V lockout. The 800 mA figure applies in step down from 3.6 V of input.
Does the output stay connected in shutdown? No. The four switch topology disconnects the load, and the shutdown current is 0.1 uA typical and 0.9 uA maximum.
How is the output voltage set? By two resistors from the 500 mV reference on the TPS63030, or fixed at 3.3 V on the TPS63031, which needs no divider.
What does the PS/SYNC pin do? Low selects power save mode for light load efficiency. High forces fixed frequency operation, and an external clock on the same pin synchronises the switching.
What is the real current limit? 1 A typical average, with a 900 mA minimum and a 1.3 A maximum, and the limit folds back to less than half of nominal on a hard short.
What inductor does it need? A 1.5 uH part, placed directly across the two switch pins with the input capacitor close by, because both switch pins carry the full current.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.