Contact Us

TPS63027YFFR

Brand: Texas Instruments
Texas Instruments TPS63027YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63027YFFR — Power Management & Signal Chain | Superb Automation

TPS63027YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63027YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63027YFFR 2 A single inductor buck boost in a 25 pin DSBGA

The TPS63027YFFR is a four switch buck boost converter that runs from 2.3 V to 5.5 V and delivers up to 2 A at an adjustable output from 1.0 V to 5.5 V, using one inductor. It switches at 2.5 MHz, the typical average current in the switches is 4.5 A, and the efficiency reaches 96 per cent in buck or boost. The body is the YFF DSBGA of 25 bumps, which puts the whole converter including its two switch pairs under a footprint that a wrist worn product can afford.

The topology is single inductor and four switch, with an automatic transition between buck and boost as the input crosses the output. In buck mode the two left switches chop and the two right switches rectify; as the input falls toward the output the part moves through a mixed sequence and into boost without a mode pin and without a dead band. A rail that holds 3.5 V while a cell falls from 4.2 V to 2.5 V crosses the output voltage in the middle of its discharge, which is exactly where the transition has to be seamless.

The quiescent current is 35 microamp, which is a different class from the nanoamp parts and is the price of the four switch topology. For a product that sleeps for long periods the 63027 is not the right choice; for a product that runs a display, a radio or a motor from a single cell, the 2 A output and the seamless transition are worth more than the standby current. The decision is a system one and should be made on the average current rather than on the datasheet headline.

Key parameters from the SLVSDK8 document

Input range2.3 V to 5.5 V
Output range1.0 V to 5.5 V, adjustable through the FB pin
Output current2 A continuous with 4.5 A typical average switch current
Switching frequency2.5 MHz typical, fixed frequency PWM with synchronous rectification
EfficiencyUp to 96 per cent in buck or boost
Quiescent current35 microamp typical
TopologyFour switch single inductor with automatic buck to boost transition
Mode pinPFM and PWM selection for light load behaviour
FeedbackExternal divider on the adjustable member
Inductor1 microhenry in the application circuit
Capacitors10 microfarad input and two 22 microfarad output capacitors in the application circuit
PackageYFF DSBGA of 25 bumps

Where the four switch topology earns its cost

A two stage arrangement of a buck followed by a boost has a band around the output voltage where neither stage regulates well, and that band is where a single cell product operates for hours. The four switch part removes the band by running a mixed sequence in the transition region, and the result is a rail that holds its level while the battery passes through it. On a product with a display and a radio, that behaviour is the difference between a clean shutdown at low battery and a reset at 20 per cent charge.

The 25 bump body is not only about size. A DSBGA puts the switch pairs and the inductor connections close together, which keeps the loop area small and the ripple low at 2.5 MHz. The penalty is that the part must be assembled on a line that can place a chip scale package and that the board needs a via structure under the bumps to carry 2 A. A customer whose line is set up for leaded parts should be looking at a different family rather than at an adapter.

The PFM and PWM selection is worth a note because it changes the behaviour at light load. In PFM the part skips cycles and the quiescent current falls, which extends the run time of a product that idles between transmissions. In PWM the ripple stays at 2.5 MHz and the output is cleaner, at the cost of a higher no load current. Both modes are available at the pin, so the choice can be made per product rather than per order code.

Where this part fits

Handheld instruments, portable medical monitors, wireless terminals, wearable displays and any single cell product where the rail has to hold across the whole discharge. Our cross reference notes are at power management cross reference and the substitution check is at how to verify a drop in replacement.

What to check before a purchase order

Check the inductor against the switch current limit rather than the output rating. In boost mode the inductor carries more than the output current, so a part that is adequate at 2 A in buck can saturate in boost, and the failure appears only when the battery is low. A 2.2 microhenry inductor with a saturation above 5 A is a safer choice than a smaller part with a 3 A rating.

Check that the assembly line can place a DSBGA and that the board carries the vias needed to remove heat and current from the bumps. A chip scale part on a board with a coarse via rule will work on a bench and fail in a drop test. The receipt check we run on these reels is at incoming inspection plan.

Questions that come up on this part

Can the output be set below 1.0 V, is a common question. The family range starts at 1.0 V, so a 0.9 V core rail needs a different device. The divider on the FB pin can be calculated for any level above the internal reference, but the part is characterised over the published range, and operating outside it is a bench result rather than a specification.

The second question is whether the 2 A rating holds at 2.5 V input. In boost mode the input current is higher than the output current and the switch limit of 4.5 A typical is what supports the rating. At the bottom of the input range the available output current is smaller than at the top, and the curves in the document are the place to read the real number for a given input and output pair.