Contact Us

TPS63001DRCR

Brand: Texas Instruments
Texas Instruments TPS63001DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS63001DRCR — Power Management & Signal Chain | Superb Automation

TPS63001DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS63001DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS63001DRCR: Buck boost converter with a fixed 3.3 V output that works from 1.8 V to 5.5 V

TPS63001DRCR is a four switch buck boost converter in the ten pin DRC body that holds a fixed 3.3 V output from an input anywhere between 1.8 V and 5.5 V, delivers up to 800 mA in boost mode and draws less than 50 uA when it is not switching in a VSON-10 body of 10 pins. The TPS63001 is the fixed 3.3 V member of the TPS6300x family, with the adjustable TPS63000 and the fixed 5 V TPS63002 alongside it. It switches automatically between step down and step up as the input crosses the output, uses synchronous rectification for efficiency, and enters a power save mode at light load that can be disabled for a fixed frequency. The load is disconnected from the input during shutdown, which is what allows a battery product to sit with the converter off and no leakage path through the inductor and the body diodes.

Order code and package

Order codeTPS63001DRCR
Input voltage1.8 V to 5.5 V
Output voltage3.3 V fixed
Output current in boost modeup to 800 mA with the input above 2.4 V
Topologyfour switch buck boost, automatic crossover
Quiescent currentless than 50 uA
Packageten pin VSON, DRC body, 3 mm by 3 mm
Temperature rangeminus 40 C to 85 C

Electrical parameters that decide the application

Switch current limit1800 mA typical average
Power save modeenabled by default, can be disabled for fixed frequency
Synchronisationpossible to an external clock in forced fixed frequency mode
Shutdownload disconnected from the input
Protectionovertemperature
Fixed output versionsTPS63001 at 3.3 V, TPS63002 at 5 V
Adjustable versionTPS63000 with an external divider
Body size3 mm by 3 mm, ten pins

Points to check before this part goes on a BOM

The 1.8 V to 5.5 V input range covers the full discharge curve of a single lithium cell with margin at both ends. A cell at 4.2 V is above the 3.3 V output and the converter steps down; a cell at 3.0 V is below it and the converter steps up. The crossover happens somewhere in the middle of the discharge, and the behaviour at that point is what separates a four switch converter from a buck boost built from two stages: the four switch topology passes through a region where all four devices switch and the efficiency dips, but the output never glitches.

Eight hundred milliamps at 3.3 V in boost mode requires the input to be above 2.4 V, which is stated as a condition rather than a limitation. Below 2.4 V the input current for the same output power rises above what the switches can carry, and the current limit takes over. The arithmetic is worth doing at end of discharge: 3.3 V at 500 mA is 1.65 W, and at 2.0 V input with 85 percent efficiency that is 970 mA of input current, close to the 1800 mA switch limit with the ripple on top. A product that needs full load at 2.0 V is asking for more than the part can give.

Fifty microamps of quiescent current is the number that decides standby life, and it is 438 mAh over a year, which is more than a coin cell holds. That sounds unusable until the number is put against a product that actually sleeps: a converter in shutdown draws far less and disconnects the load, so a product that can turn the rail off does not pay the 50 uA. A product that must keep a rail alive to run a real time clock should use a converter with a lower quiescent current or run the clock from the battery directly.

Disconnecting the load in shutdown is a subtle but important behaviour. A boost converter has a DC path from the input to the output through the inductor and the body diode of the upper switch, so a load connected to the output is fed from the battery even when the converter is off, at one diode drop below the input. A four switch topology can open that path, which is why a product with this part can sit in a box for a year and still have a charge.

Power save mode is on by default and it changes the output ripple rather than the average. At light load the converter skips cycles and the output rises and falls within a window set by the comparator, which is a few tens of millivolts. That is fine for a digital rail and not fine for an analog one, and the mode can be disabled to get a fixed frequency and a lower ripple at the cost of the light load efficiency. The pin that selects it is a board decision, so a product that needs both behaviours in different modes of operation needs a controller that can drive it.

One thousand eight hundred milliamps of average switch current limits the output in step up mode and not in step down mode. In step down the switch current is the output current plus the ripple divided by the duty cycle, and at a 4.2 V input to a 3.3 V output the duty is high enough that 800 mA of output is well inside the limit. In step up the switch current is the input current, which is larger than the output current by the ratio of the voltages, and that is where the limit arrives first. A board that needs its full load at the lowest input is limited by the switch, not by the rating.

A 3 mm by 3 mm body with four switches inside has two hot loops rather than one, because the boost half and the buck half each have their own. The input capacitor serves the buck half and the output capacitor the boost half, and in the crossover region both are switching. The routing guidance in the document places the inductor and the two capacitors close to their own pins, which is a different arrangement from a buck converter with a single loop, and a board that copies a buck routing produces ringing at the crossover.

Where this order code fits

This order code belongs on products that run from a single lithium cell or from two or three alkaline cells, where the rail has to stay at 3.3 V while the battery moves from 4.2 V down to 2.5 V. It is also the part chosen where the input can be above or below the output during normal operation, because a buck alone drops out and a boost alone cannot start, and a product that does both needs a converter that crosses over without a glitch. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What happens when the input equals the output? The converter passes through a region where it switches between the two modes, and the output stays regulated without a glitch. The efficiency dips in that region because all four switches are active, and the dip is the price of a four switch topology that never has a dead band.

Can it deliver 800 mA from a 2.0 V input? Not at 3.3 V out. Eight hundred milliamps at 3.3 V is 2.64 W, which at 2.0 V and 85 percent efficiency needs 1.55 A of input current, close to the 1800 mA switch limit before the ripple is counted. The full rating is specified with the input above 2.4 V.

Is 50 uA low enough for a battery product? It is 438 mAh over a year, so a product that leaves the rail alive pays more than a coin cell holds. The shutdown path disconnects the load and draws far less, so the answer depends on whether the product can turn the rail off, and a real time clock needs a supply that is not this rail.

Why does the load disconnect matter? Because a boost converter otherwise feeds the output through the inductor and a body diode even when it is off, which drains the battery through the load. The four switch topology opens that path in shutdown, so the product can be stored without a leakage current.

SUPERB holds and sources this converter line against the exact order code, with the reel, date code and country of origin stated on the offer. When a rail has to move to a second part, the Component Lead Time Solutions page sets out the checks that separate a working substitute from one that fails on the bench.