Contact Us

TPS62A02APDDCR

Brand: Texas Instruments
Texas Instruments TPS62A02APDDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62A02APDDCR — Power Management & Signal Chain | Superb Automation

TPS62A02APDDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62A02APDDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62A02APDDCR 2 A buck in the SOT-23 body

The TPS62A02APDDCR is the 2 A member of the TPS62A0x family in the DDC SOT-23 body, the leaded package that a board takes when the SOT-563 is not available or when a wider pin pitch is needed for inspection. It runs from 2.5 V to 5.5 V, switches at 2.4 MHz, and sets its output with a divider on the FB pin from 0.6 V up to the input. The A suffix marks the forced PWM behaviour and the P in the body code marks the SOT-23 option.

Electrically it is the same converter as the SOT-563 member: 100 milliohm high side and 67 milliohm low side, a 600 mV reference with a 594 mV to 606 mV window at 25 degrees, quiescent current below 23 microamp in the non switching state, 0.01 microamp of shutdown current, and an undervoltage lockout at 2.3 V to 2.5 V rising. What changes is the thermal path and the assembly process, not the control loop.

The SOT-23 body suits a line that runs a leaded only process, and it suits a product that has to be inspected under magnification after reflow. The trade is a larger footprint than the SOT-563 and less copper per pin for heat, so a 2 A rail in the DDC body at high ambient has to be checked against the enclosure temperature rather than against the data sheet alone.

Key parameters from the SLUSEG9E document

Input range2.5 V to 5.5 V
Output range0.6 V to the input voltage through the FB divider
Output current2 A on this member
Switching frequency2.4 MHz fixed, forced PWM operation on the A member
Switch resistance100 milliohm high side and 67 milliohm low side on the 2 A body
Feedback voltage600 mV nominal with a 594 mV to 606 mV window at 25 degrees
Quiescent currentBelow 23 microamp in the non switching state
Shutdown current0.01 microamp typical
UVLO2.3 V to 2.5 V rising
Thermal noteContinuous 2 A with an input below 3.3 V or an ambient above 85 degrees can reach thermal shutdown
Output capacitanceQuoted by output range in the document, 1.0 microhenry inductor in the application circuit
PackageDDC SOT-23 body with six pins

What changes when the same silicon moves to a leaded body

The control loop, the current limit and the reference are identical to the SOT-563 member, so a change of body does not change the electrical behaviour of the rail. What changes is the thermal resistance and the assembly: a leaded body spreads heat through the pins into the solder joints, and the copper on the board is the only heat sink. On a board with a small pad the same 2 A that runs cool in the SOT-563 can run hotter in the SOT-23, which is the opposite of what most people expect from a bigger package.

The leaded body also changes the receipt check. A SOT-23 can be inspected for solder fillet and for coplanarity with a simple optical check, while a SOT-563 with a thermal pad needs an X-ray or a thermal via pattern that can be verified. For a product with a traceability requirement, that difference is worth more than the footprint.

The 2.4 MHz carrier and the 100 per cent duty mode are unchanged. At the bottom of the input range the part passes the input through and the output follows the input less the drop across the two switches, which at 2 A and 167 milliohm in series is about 330 millivolt. A 3.3 V rail therefore holds down to about 3.6 V input and then follows the battery down, which is the behaviour to describe to a customer who asks how long the product runs on a nearly empty cell.

Where this part fits

Leaded assembly lines, industrial boards with a conformal coat requirement, motor and relay driver rails and any product that needs 2 A from 5 V in a package that can be inspected. The cross reference notes are at pin to pin cross reference and the family equivalents are at power management cross reference.

What to check before a purchase order

Check the body code and do not substitute across it. DRL is the SOT-563, DDC is the SOT-23, and the two are not interchangeable on a board. The order code carries both the current and the body, and the packing label is where to confirm it on receipt, because the parts look similar in a bag and are impossible to tell apart after reflow.

Check the thermal path at the actual ambient and with the actual copper. The vendor note about continuous 2 A below 3.3 V input or above 85 degrees ambient applies to the whole family, and a leaded body in a sealed enclosure reaches that condition earlier than the data sheet curve suggests. The receipt check is at incoming inspection plan.

Questions that come up on this part

Can the SOT-23 member be used in place of the SOT-563 on a board that is already released, is a common question. Not without a board change, because the footprints differ. What can be done is a family change on a new board, and that is a board question for the customer rather than a substitution for the purchasing desk.

The second question is whether the forced PWM version can be swapped for the power save version. It can electrically, and the difference appears only at light load: the power save part will drop its frequency and its quiescent current, and a radio on the same board will see a different noise spectrum. A product that passed emissions with one version may need a retest with the other.