Contact Us

TPS62A02ADRLR

Brand: Texas Instruments
Texas Instruments TPS62A02ADRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62A02ADRLR — Power Management & Signal Chain | Superb Automation

TPS62A02ADRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62A02ADRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62A02ADRLR 2 A buck in a SOT-563 body

The TPS62A02ADRLR is the 2 A member of the TPS62A0x family in the DRL SOT-563 package of 1.6 mm by 1.6 mm. It runs from 2.5 V to 5.5 V, switches at 2.4 MHz, and regulates an adjustable output from 0.6 V to the input voltage with a 600 mV feedback reference. The A suffix marks the forced PWM behaviour, which keeps the switching frequency fixed at light load for a rail that feeds a radio or a converter that cannot tolerate a variable ripple spectrum.

The family shares one document across six order codes: 1 A and 2 A members, in the DRL SOT-563 body and the DDC SOT-23 body, with power save and forced PWM options. The switch resistances are 180 milliohm and 120 milliohm on the 1 A DRL body, and 100 milliohm and 67 milliohm on the 2 A and DDC bodies. Quiescent current is below 23 microamp and the feedback window at 5 V in and 1.8 V out is 594 mV to 606 mV, with 591 mV to 609 mV over the full temperature range.

The 2.4 MHz carrier is the reason the whole converter fits in a 1.6 mm square with a 1 microhenry inductor and two 10 microfarad capacitors. It is also the reason the input capacitor has to be placed within a millimetre of the VIN pin: at that frequency the loop area carries the full pulsed current, and a part placed on the far side of the body will produce an input ripple that no amount of output capacitance can fix.

Key parameters from the SLUSEG9E document

Input range2.5 V to 5.5 V
Output range0.6 V to the input voltage, set by a divider on the FB pin
Output current2 A on this member, 1 A on the A01 members
Switching frequency2.4 MHz, with a 100 per cent duty mode at the bottom of the input range
Switch resistance180 milliohm high side and 120 milliohm low side on the 1 A DRL body, 100 and 67 milliohm on the 2 A body
Feedback voltage600 mV nominal, 594 mV to 606 mV at 25 degrees and 591 mV to 609 mV over temperature
Quiescent currentBelow 23 microamp in the non switching state
Shutdown current0.01 microamp typical with the enable low
UVLO2.3 V to 2.5 V rising
Operation modeForced PWM on this A member, power save on the base members
Power goodOpen drain on the versions that carry the pin
PackageDRL SOT-563 of 1.6 mm by 1.6 mm with six pins

Forced PWM as a choice rather than a default

In power save mode the converter skips cycles at light load, and the output ripple becomes a low frequency burst that a radio or an audio chain can hear. In forced PWM the part switches at 2.4 MHz regardless of the load, the ripple stays a clean 2.4 MHz triangle, and the cost is that the no load current rises from microamps to milliamps. A product that transmits takes forced PWM, a product that sleeps takes power save, and the order code is how the choice is made.

The 2 A rating in a 1.6 mm square body is a thermal statement. At 5 V to 1.8 V and 2 A the converter dissipates about 400 milliwatt, most of it in the two switches and the inductor, and a SOT-563 with a small pad has limited area to spread it. The vendor notes that continuous operation at 2 A with an input below 3.3 V or an ambient above 85 degrees can reach thermal shutdown, which is the honest description of the limit and the reason the 1 A member exists in the same body.

The 100 per cent duty mode matters at the bottom of the input range. When the battery falls to the output voltage plus the drop across the switches, the part stops switching and passes the input through, so a 3.3 V rail holds until the battery is nearly empty instead of dropping out at 3.6 V. That behaviour is what makes a single cell product usable to the end of its discharge curve.

Where this part fits

Point of load rails on handheld instruments, camera modules, radio front ends, small motor drivers and any board that needs 2 A from a 5 V or a lithium cell rail in a 1.6 mm square. Our cross reference notes are at pin to pin cross reference and the substitution check is at how to verify a drop in replacement.

What to check before a purchase order

Check both the suffix letter and the body code. The A members are forced PWM and the base members are power save, and DRL is the SOT-563 while DDC is the SOT-23. The two bodies do not share a footprint, and the two behaviours do not share a ripple spectrum, so a reel that matches on current and not on the rest will pass a functional test and fail an emissions test.

Check the inductor against the 2.4 MHz carrier and against the current limit rather than the 2 A rating, and check the derating against the enclosure temperature. The receipt and marking check we run is at incoming inspection plan.

Questions that come up on this part

Is the DRL body a drop in for the DDC body, is a common question. It is not, because the two packages have different footprints and different thermal pads, even though the electrical function is the same. A board that was routed for one and populated with the other will not solder correctly, and a reflow that looks acceptable can leave the thermal pad unconnected.

The second question is whether the output can be set to 0.9 V with the 600 mV reference. It can, with a divider ratio of 1.5, which is inside the useful range. Below about 0.6 V the divider ratio approaches one and the tolerance of the resistors starts to dominate, so a core rail below 0.6 V needs a part with a lower reference rather than a tighter resistor pair.