TPS62933PDRLR
Product Specifications
TPS62933PDRLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62933PDRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62933PDRLR: 3 A synchronous buck, 3.8 V to 30 V input, power good output
TPS62933PDRLR is a 3 A synchronous step-down converter with a 30 V input rating and a power good output in a SOT-583 body of 8 pins. This is the member of the TPS6293x family that brings out a power good pin instead of a soft start pin, which makes it the one to pick when several rails have to come up in order. The input range covers a 24 V industrial bus with margin, the output goes to 22 V, and the quiescent current is 12 microamp for the pulse frequency members.
Order code and package
| TPS62933PDRLR | Active, SOT-5X3 eight pin, 4000 pieces on a large reel, SN finish, MSL-1-260C-UNLIM |
| TPS62932 | the 2 A member with a soft start pin, same body and reel |
| TPS62933 | 3 A with a soft start pin |
| TPS62933F | 3 A, forced continuous conduction instead of pulse frequency modulation |
| Temperature range | minus 40 to 150 degrees junction |
Electrical parameters that decide the application
| Input voltage | 3.8 V to 30 V |
| Output voltage | 0.8 V to 22 V |
| Continuous current | 3 A on this member, 2 A on the TPS62932 |
| Reference | 0.8 V, plus or minus 1 per cent at 25 degrees |
| Quiescent current | 12 microamp on the pulse frequency members |
| High side and low side resistance | 76 milliohm and 32 milliohm |
| Maximum duty cycle | 98 per cent |
| Compensation | internal, peak current mode |
Family variants and how they differ
| TPS62933P | power good pin in place of the soft start pin, this order code |
| TPS62933 and TPS62932 | soft start pin, the ramp time is set by a capacitor |
| TPS62933F | forced continuous conduction, lower ripple at light load |
| TPS62933O | out of audio mode, avoids the audible tone at light load |
| Body | 1.6 mm by 2.1 mm, eight pins |
Points to check before this part goes on a BOM
The P in the suffix costs the soft start pin. This member brings out power good and no soft start, so the ramp time is fixed internally. A board that needs a long ramp to control inrush on a large output capacitance cannot stretch it here and needs the sibling with the SS pin. A board that needs to tell the next converter when to start needs this one. The two requirements do not fit in eight pins.
30 V input against a 24 V bus is only 6 V of margin. A 24 V industrial rail with a 10 per cent transient reaches 26.4 V, which is inside. A 24 V rail with a 25 per cent surge does not. The 76 milliohm high side switch is rated for the current, and the input rating is what decides whether the part belongs on the rail at all.
12 microamp is a pulse frequency figure. It applies to the TPS62932, TPS62933 and TPS62933P when they are allowed to drop pulses at light load. The forced continuous member draws more at no load because it never stops switching. On a rail that sits idle for long periods, the difference between 12 microamp and a few milliamp is the difference between staying inside a sleep budget and not.
98 per cent duty cycle is what makes a 24 V to 22 V rail possible. It lets the converter pass the input through when the input is close to the output, which is useful at the bottom of a sagging bus. As with every converter, the rail is no longer regulated in that condition, so a downstream load has to accept the input voltage appearing on its supply.
Power good has a threshold, and it is not the regulation window. The pin asserts when the output is inside its window, and it is an open drain output that needs a pull up. A sequencer that waits for power good has to allow for the delay through the pull up and the comparator, so the next rail starts a few millisecond later than the first one reaches regulation.
The body is 1.6 mm by 2.1 mm and the thermal path is the ground pad. At 3 A the switch losses and the inductor current both run through that pad. A four layer board with vias under the pad is normal for this current. Two layer boards work at lower current or with a large copper pour, and the current rating does not change between the two arrangements.
The 22 V output ceiling is a real limit for a 24 V input. A 24 V to 24 V conversion is not possible with this part even at 98 per cent duty, because 22 V is the output maximum. Rails that need to sit at the input voltage need a different topology, and a customer asking for a 24 V to 24 V clean up is asking for the wrong device.
The four members differ in behaviour, not in footprint. They share the body, the pinout and the reel size, so a substitution during a shortage is physically possible. The behaviour difference is at light load and in the ramp, which is exactly where a substitution is most likely to be noticed after the product has shipped.
The ripple in the inductor decides the output capacitor. The 3 A rating is an average, and the peak sits above it by half the ripple. A small inductor gives a fast transient and a larger ripple for the output capacitor to absorb. The internal compensation sets a range of values that work, and moving outside it produces either a slow loop or an unstable one.
The reel is 4000 pieces in an eight pin body. That suits a volume line, and it also means the practical minimum is a full reel unless a distributor breaks it. For a prototype run of twenty boards a cut tape is the route, and with a level 1 moisture level no bake is needed once the reel has been opened.
The eight pin body keeps the switch node loop short. A short switch node loop is what keeps the radiated field small, and the pinout is arranged for it. Routing the inductor away from the part to suit a connector defeats that, and the result shows up as conducted emissions at the input.
Sequencing with a power good output
A rail that must come up after another one waits on this pin instead of a fixed delay, so a slow start on the first rail does not leave the second one running into an unpowered load.
The pin is open drain and needs a pull up to the rail it supervises or to a lower logic rail, which decides whether the signal is compatible with the device that reads it.
Where this order code fits
It runs 3 A rails from 24 V industrial buses and 12 V battery rails, where a 30 V input rating and a power good signal are both required. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can the output be set above the input? No. The output maximum is 22 V and the part is a step-down converter, so the input always has to be above the output by the dropout of the loop. A rail that needs to sit at the input voltage is not a buck converter case.
What is the difference between this and the plain TPS62933? The pin brought out: power good here, soft start on the plain part. Everything else, including the body, the reel and the current rating, is the same.
Is external compensation needed? No. The loop is internally compensated and expects ceramic output capacitors. The transient performance is set by the output capacitance, so the value is chosen from the load step rather than from a stability minimum.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.