Contact Us

TPS62932DRLR

Brand: Texas Instruments
Texas Instruments TPS62932DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62932DRLR — Power Management & Signal Chain | Superb Automation

TPS62932DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62932DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62932DRLR: a 30 V, 2 A synchronous buck converter in SOT583

TPS62932DRLR is a 3.8 V to 30 V synchronous step-down converter in a SOT-5X3 (DRL) body of 8 pins. The DRL body is 1.60 mm by 2.10 mm with eight pins, and the reel marking is 2932, which is how the 2 A version is told apart from the 3 A TPS62933DRLR marked 2933 on the same line. Both parts share the pin out and the 4000 piece reel.

Order code and package

TPS62932DRLRSOT-5X3 (DRL), 8 pins, 4000 piece large reel, marking 2932, -40 to 150 C
TPS62933DRLRsame body, 3 A version, marking 2933, same 4000 piece reel
TPS62933FDRLRforced continuous version, marking 933F
TPS62933PDRLRpower good version, marking 933P
TPS62933ODRLRout of audio version, marking 933O
Finish and floor lifeRoHS yes, Sn lead finish, MSL level 1 at 260 C, unlimited floor life

Electrical parameters that decide the application

Input and output3.8 V to 30 V in, 0.8 V to 22 V out, 32 V absolute maximum on VIN and on SW in dc
Current2 A continuous on the TPS62932, 3 A on the TPS62933 and its variants, against a 3.8 A to 4.5 A low side current limit on the 3 A parts
Reference0.8 V plus or minus 1 percent at 25 C
Switching devices76 mOhm high side and 32 mOhm low side integrated NMOS
Quiescent current12 uA typical non-switching on the TPS62932, the TPS62933 and the TPS62933P, 125 uA on the forced continuous TPS62933F
Shutdown current45 uA maximum with EN pulled to 0 V
Duty cycle98 percent maximum, which is what lets the part hold regulation when the input sags towards the output
Soft start5.5 uA typical charge current into the SS pin on the TPS62932, TPS62933 and TPS62933F, 4.5 uA minimum and 6.5 uA maximum
Spread spectrum6 percent internal spread oscillator, on by default, there to move peak emissions off a single frequency
Reverse current1.2 A to 3.6 A limit on the forced continuous TPS62933F, which allows the inductor current to run negative
Thermal112.2 C/W junction to ambient on a JEDEC board, 60.2 C/W on the vendor EVM with two layers and two ounce copper
Absolute maximum32 V on VIN and SW, 6 V on EN and FB

Family variants and how they differ

TPS62933identical pin out, 3 A instead of 2 A, and a 3.8 A to 4.5 A low side limit instead of the lower ceiling of the 2 A part
TPS62933Fforced continuous conduction, no pulse frequency modulation, chosen where output ripple at light load matters more than standby current
TPS62933Pbrings the PG pin out in place of SS, so soft start time is fixed and power good is available
TPS62933Oout of audio mode, added to keep the switching tone out of the audible band at light load
The 2 A versionkeeps the 12 uA quiescent current and the pulse frequency modulation of the base part, so it is the one to specify when the rail sits idle most of the time

Points to check before this part goes on a BOM

The 2 A and 3 A parts are interchangeable on the board but not on the BOM. Same eight pins, same 1.60 mm by 2.10 mm body, same 4000 piece reel, and the only physical clue is the marking, 2932 against 2933. A line that reels both versions has to read the marking rather than trust the reel label, because a 3 A part fitted where a 2 A part was qualified raises the low side current limit and changes the fault behaviour.

Conduction loss is the number that decides whether the 2 A version is enough. At 3 A the 32 mOhm low side switch alone burns 288 mW, and the 76 mOhm high side adds roughly the same again at a 12 V to 5 V conversion, which is why the 3 A ceiling belongs to the TPS62933 and the 2 A part stays on rails that draw under two amps.

Pulse frequency modulation is the reason to keep the TPS62932 rather than fit the forced continuous version for convenience. At light load the base part drops cycles and settles at 12 uA of quiescent current, while the forced continuous part holds 125 uA and keeps ripple flat. A battery backed rail wants the first behaviour, an analog front end that cannot tolerate ripple at no load wants the second.

The 98 percent maximum duty cycle is worth checking against the real input sag. A 5 V rail fed from a 6 V bus is well inside it, but a 3.3 V rail fed from a 3.8 V input sits close enough that the dropout path, not the switching loop, sets the minimum input.

Mixing the 2 A and 3 A parts on one line

A BOM that names TPS62932DRLR and a stock list that offers TPS62933DRLR are one part number apart and look identical in a photo. The electrical tables differ in the low side current limit, 3.8 A to 4.5 A on the 3 A version against the lower ceiling of the 2 A part, and the quiescent current holds at 12 uA on both. Substituting upwards is usually harmless for a rail that draws under two amps, substituting downwards on a rail that needs three is a thermal failure waiting for a warm day.

The reel quantity does not help tell them apart either, both are 4000 pieces on a large reel with the same MSL level 1 rating at 260 C. The practical control is the top marking, 2932 against 2933, read at incoming inspection rather than trusted from the reel label. A distributor quoting a second source for this family should state which of the five variants is being offered and against which ordering string, because the family carries five pin compatible members and only four of them are stocked on a normal schedule.

Where this order code fits

It serves 12 V and 24 V industrial rails, after-market automotive boards that need the 30 V input ceiling, and any point of load converter that has to keep a low standby draw. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can a TPS62933DRLR replace a TPS62932DRLR on the same pads? The pad and the pin out are the same, so it fits. The difference is the current ceiling and the low side limit, so the replacement is safe only where the rail draws less than 2 A and the higher limit does not change what the board does under a fault.

Why does the data sheet quote two thermal numbers? 112.2 C/W is a simulated JEDEC board used for comparison between packages, and 60.2 C/W is measured on the vendor EVM with two layers of two ounce copper. The second is the one that means something for a real board, and the vendor states that the first cannot be used for thermal work.

What sets the minimum input voltage? The 3.8 V operating floor plus the 98 percent duty cycle ceiling. Below 3.8 V the part stops switching, and close to that floor the conversion ratio rather than the current limit becomes the constraint.

How is the 2 A version identified on a mixed line? By the top marking, 2932 against 2933, or by the ordering string on the reel. The body size, the pin count and the reel quantity are identical, so neither the footprint nor the packaging tells the two apart.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.