Contact Us

TPS62902RPJR

Brand: Texas Instruments
Texas Instruments TPS62902RPJR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62902RPJR — Power Management & Signal Chain | Superb Automation

TPS62902RPJR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62902RPJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62902RPJR: 17 V input, 2 A synchronous buck in a 1.5 mm by 2 mm package with 4 uA quiescent current

TPS62902RPJR is a 2 A synchronous step down converter with a selectable 2.5 MHz or 1.0 MHz switching frequency and a 4 uA quiescent current in a VQFN-HR body of 9 pins. It runs from 3 V to 17 V, delivers 2 A continuously, and switches at 2.5 MHz or 1.0 MHz selected on the configuration pin. The feedback is either an external divider from 0.6 V up or one of sixteen internal settings between 0.4 V and 5.5 V, and the high side FET is 62 mOhm against 22 mOhm on the low side.

Order code and package

TPS62902RPJR9-pin VQFN-HR (RPJ), 2.00 mm by 1.50 mm, 0.5 mm pitch, large reel
Output current2 A continuous
Feedback accuracyplus or minus 0.9 per cent over -40 C to 150 C
Output voltage, external divider0.6 V to 5.5 V
Output voltage, internal setting16 options between 0.4 V and 5.5 V
Operating junction temperature-40 C to 150 C

Electrical parameters that decide the application

Input voltage range3.0 V to 17 V
Output current2 A continuous
Switching frequency2.5 MHz or 1.0 MHz, selected by the configuration pin
High side FET on resistance62 mOhm at 500 mA and above 4 V in
Low side FET on resistance22 mOhm at 500 mA and above 4 V in
Quiescent current4 uA typical, no load, not switching
Feedback voltage0.6 V nominal with an external divider
Power good thresholds96 per cent rising, 93 per cent falling, of the nominal output
Undervoltage lockout hysteresis150 mV
Soft start and trackingadjustable, tracking gain tolerance plus or minus 8 per cent

What the configuration pin selects

Internal dividerone of sixteen output voltages, chosen without an external divider, so no divider current
External dividerany output from 0.6 V up, at the cost of a standing divider current
2.5 MHzthe smallest inductor and the fastest transient response, with higher switching loss
1.0 MHzbetter efficiency at heavy load and a larger inductor, still small in this package
Power save modeautomatic entry at light load, which is where the 4 uA quiescent current applies
Forced pulse width modulationconstant frequency at any load, for a rail that has to stay quiet
Output dischargethe output is pulled down when the part is disabled, selectable on the pin
Power goodopen drain flag, needs a pull up, tracks the feedback node

Points to check before this part goes on a BOM

The 2.5 MHz setting is what allows a 1 uH inductor in a 2 mm package, and it is also what limits the input voltage at which the part can switch at that rate. At 17 V in and 0.6 V out the on time at 2.5 MHz is below the minimum controllable pulse, so the part has to skip cycles and the ripple grows. A rail with a large step down ratio belongs on the 1.0 MHz setting, and the ripple at 2.5 MHz is worse rather than better.

The internal divider is the feature that pays for itself on a battery product. Sixteen settings between 0.4 V and 5.5 V remove the divider current entirely, and on a rail that is always on, a 100 uA divider costs more than the converter's own 4 uA quiescent current in the same ratio. The accuracy is also better, because the internal divider is trimmed and the external one is limited by the resistor tolerance.

The four microamp quiescent current applies in power save mode at light load, and it is the number that matters on a product that sleeps. In forced pulse width modulation the part keeps switching at the selected frequency with no load, and the supply current is then tens of milliamps rather than microamps. A rail that has to be quiet and a rail that has to be frugal are two different settings of the same pin.

The power good flag is referenced to the feedback node, with thresholds at 96 per cent rising and 93 per cent falling. That window is wide enough that a rail which is sagging under a load step can clear the flag before it is actually out of regulation, so a controller that treats the flag as a hard fault will see trips that are not faults. It is a sequencing signal, and the window is why.

The part has no external bootstrap capacitor, which removes a component and a pin. That is not only a cost saving: the bootstrap capacitor is the part that fails when the switching node rings, and with it inside the package the ringing is contained. What the board has to do instead is keep the input capacitor close, because the high side gate drive current now comes from the same loop.

The DCS-Control loop has no external compensation, so the output capacitor range and the inductor value are the only two things the board can get wrong. A 1 uH inductor at 2.5 MHz with 22 uF of ceramic output capacitance is the vendor starting point. Doubling the inductance to reduce ripple moves the loop and can make the transient response slow enough to trip the power good flag on a load step.

The 62 mOhm high side and 22 mOhm low side are quoted above 4 V in. Below that the FETs are driven with less gate voltage and the resistance rises, which is why a 3.3 V to 1.8 V rail runs hotter than the same current at 12 V in. The efficiency curve at 3.3 V in is the one to read for a rail fed from a lithium cell, not the curve at 12 V.

The junction temperature rating goes to 150 C, and that is a rating rather than a target. At 2 A out and 12 V in the dissipation in this package is small, but at 17 V in and 1 V out at 2 A the switching loss and the low side conduction loss together put the junction close to the limit on a board without copper. The thermal pad is the only path, and the via count in the vendor example is the minimum.

Soft start and tracking share a pin, and the tracking gain tolerance is plus or minus 8 per cent. That tolerance is fine for a rail that follows another rail loosely and it is not fine for a rail that has to match a second rail within a few millivolts, such as a DDR termination. A rail with a tight tracking requirement needs a different arrangement rather than a tighter resistor.

The output discharge option is selected on the configuration pin and it matters for sequencing. A rail that is turned off and left to fall on its own load can hold a residual voltage that a downstream part reads as a valid supply, and the result is a device that starts in an undefined state. With discharge selected the rail falls to zero within a defined time after the enable pin goes low.

The package is 0.5 mm pitch with nine pins plus a pad, and the pinout is arranged so that a single layer route is possible. That only works when the input capacitor sits on the same side as the pins and the inductor is placed against the switch node. On a two layer board the return path under the part has to be continuous, or the switching current loops through the ground plane and the emission rises.

The part is one member of a family that differs in current rating and pin configuration, and the same body is used across rows. A substitution during a shortage from a 1 A member to this 2 A member is safe on current, but the internal divider option list and the configuration pin behaviour are not identical across every row. The substituted part has to be checked against the pin function table rather than against the front page.

Where this order code fits

It sits on a 12 V or 5 V rail in an industrial controller, a building automation node or a portable instrument, producing the low voltage core rail from a wide input with a package small enough to fit beside the processor. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Do I need an external divider? Only if the rail is not one of the sixteen internal settings. With the internal divider selected there is no divider current at all, which is the right choice on a battery product. The external divider covers any voltage from 0.6 V to 5.5 V.

What is the difference between 2.5 MHz and 1.0 MHz? The higher frequency allows a 1 uH inductor and gives the fastest transient response, at the cost of switching loss. The lower frequency gives better efficiency at heavy load and a larger inductor, and it is the better choice when the input to output ratio is large.

Can it run from a 12 V rail and deliver 2 A? Yes, the input range covers 12 V and the output current is 2 A continuous. What changes with the ratio is the dissipation, so the junction temperature has to be checked at 12 V in rather than at 5 V in.

How accurate is the output? The feedback is trimmed to plus or minus 0.9 per cent over the full temperature range, and the power good window around it is wider than that, which is deliberate so the flag does not chatter.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.