TPS62871Y1QWRXSRQ1
Product Specifications
TPS62871Y1QWRXSRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62871Y1QWRXSRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62871Y1QWRXSRQ1 9 A automotive buck with a fixed start up setting
The TPS62871Y1QWRXSRQ1 is the same 9 A automotive converter as the base TPS62871 member, with the start up voltage option carried in the order code rather than set by resistors on the board. It runs from 2.7 V to 6 V, regulates 0.4 V to 1.0375 V in 2.5 mV steps, switches at 1.5 MHz or 2.25 MHz, and reaches a junction range of minus 40 to plus 150 degrees. The body is the QFN with wettable flanks, and the part is stackable with the other members of the TPS6287x-Q1 family for more current.
The point of the option code is repeatability. A board that brings up a processor core at a fixed voltage does not need the VSEL resistor network, and every resistor removed is a tolerance term and a placement that can go wrong on a build variant. The device reads its setting at start up, the I2C interface remains available for a change at run time, and the power good window of 96 to 98 per cent and 104 to 106 per cent is referenced to whatever level the part was ordered with.
Because the setting lives in the order code, the purchasing detail matters more than usual. The vendor addendum lists the family under strings such as TPS62873N0QWRXSRQ1, where the letter and digit pair after the base number encodes the start up voltage. A catalogue entry that carries a Y1 in that position has to be matched against the addendum before a reel is bought, and our desk treats this as a confirm before order item rather than a stock item.
Key parameters from the SLVSFJ3E document
| Input range | 2.7 V to 6 V, UVLO 2.5 V to 2.6 V rising with 90 mV of hysteresis |
| Output range | 0.4 V to 1.0375 V in 2.5 mV steps |
| Output current | 9 A on this member, stackable with the 6 A, 12 A and 15 A members |
| Start up setting | Encoded in the order code, with I2C available for a change at run time |
| Switching frequency | 1.5 MHz or 2.25 MHz selectable, spread spectrum option available |
| Output accuracy | 1 per cent, with remote sense closing the loop at the load |
| Power good | 96 to 98 per cent falling and 104 to 106 per cent rising, referenced to the ordered level |
| Thermal shutdown | 170 degrees junction with a thermal warning before the shutdown |
| Junction range | Minus 40 to plus 150 degrees |
| Interface | I2C plus MODE and SYNC pins for frequency and phase setting |
| Output discharge | Resistive discharge path when the converter is disabled |
| Package | QFN with wettable flanks, AEC-Q100 qualified |
Why an option code beats a resistor network
A divider on a VSEL pin is two components per rail and two chances for a build variant to be wrong. On a board with four core rails, that is eight components and eight placements, and the failure mode is a rail at the wrong voltage that looks like a converter fault. An option code removes all of it: the part arrives with the setting inside, the board carries no components for that function, and the bill of materials names the rail by the order code rather than by a resistor value.
The trade is procurement. An option code is a factory programmed item with a lead time and a minimum quantity, and a distributor may hold the base part while the option has to be ordered. That is why our desk confirms the string against the vendor addendum before quoting, and why a customer who needs five pieces next week is usually better served by the base part with the VSEL pins than by an option that ships in six weeks.
The register interface stays available on an option part. A system that boots at the ordered voltage can still move the rail afterwards, which is what a processor does when it shifts into a low power state. The important detail is that the start up level is a hardware fact and the run time level is a software decision, and a fault in the software cannot leave the rail at a level that the board was not signed off for.
Where this part fits
Automotive core rails that must come up at a fixed voltage without a resistor network, ADAS and sensor fusion supplies, FPGA and ASIC rails in a vehicle and any board where the same converter is used at several voltages across variants. The cross reference notes are at power management cross reference and the drop in check is at how to verify a drop in replacement.
What to check before a purchase order
Check the option pair against the vendor addendum before anything else. The addendum prints the orderable strings by start up voltage, and a string that does not appear there is not a published row, whatever a distributor listing says. Our page states the setting the part is used for and leaves the confirmation to the order record, which is the honest position for an option coded item.
Check the quantity and the lead time. An option coded part is often a factory order with a large minimum, so a prototype that needs ten pieces may have to run on the base member with VSEL resistors and switch to the option part at production. The receipt and marking check is at incoming inspection plan.
Questions that come up on this part
Is the Y1 setting 0.9 V, is a fair question, and the honest answer is that the pair has to be read from the addendum rather than guessed, because the encoding is not a simple decimal. A customer who needs a specific rail should name the voltage and let the order code follow, not the other way round.
The second question is whether the option part can replace the base part on an existing board. It can, provided the VSEL resistors are removed or left open, because the part reads its setting at start up and a resistor network that was set for a different level would otherwise fight the programmed value. Leaving the resistors in place is the one way to make a correct part behave like a wrong one.