Contact Us

TPS628610YCHR

Brand: Texas Instruments
Texas Instruments TPS628610YCHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS628610YCHR — Power Management & Signal Chain | Superb Automation

TPS628610YCHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS628610YCHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS628610YCHR 1 A buck with an I2C and VSEL interface

The TPS628610YCHR is the 1 A member of the TPS6286x line, a synchronous step down converter that runs from 1.75 V to 5.5 V and regulates an output from 0.4 V to 1.9875 V. What separates it from a conventional point of load converter is the control interface: the output can be set by the I2C bus, by the VSEL pins, or by both, and the switching frequency can be pushed up to 4 MHz. The body is the YCH chip scale package, and the whole converter needs one inductor of 0.47 microhenry and two small ceramic capacitors.

The family has a 0.6 A member and a 1 A member, and all of them keep the same register map. Output accuracy in PWM mode is 1 per cent across the operating range, the internal soft start reaches 95 per cent of the nominal output in 0.2 milliseconds, and the undervoltage lockout sits at 1.75 V rising with hysteresis below. The high side peak current limit on the 1 A member is 1.3 A minimum and 1.55 A typical, and the high side on resistance is 170 milliohm in one body and 115 milliohm in the other.

The interface is what makes this part interesting for a system that has to change a rail voltage at run time. A processor that drops its core voltage in a low power state can do it over I2C in one write rather than by gating the rail and waiting for a restart, and the same bus can read back the state of the converter for a fault log. The price is that the rail is now controlled by software, so a software fault can leave a rail at the wrong voltage, and a product that cannot tolerate that keeps the VSEL pins as the primary setting.

Key parameters from the SLUSDU8G document

Input range1.75 V to 5.5 V, UVLO 1.75 V rising
Output range0.4 V to 1.9875 V, set by I2C, by the VSEL pins, or by both
Output current1 A on this member, 0.6 A on the TPS62860
Switching frequencyUp to 4 MHz, set by register or by the frequency select pin
Output accuracy1 per cent in PWM mode with no load over the specified temperature window
Current limitHigh side peak 1.3 A minimum and 1.55 A typical on this member
High side resistance170 milliohm in one body and 115 milliohm in the other
Soft startInternal ramp reaching 95 per cent of the nominal output in 0.2 milliseconds
InterfaceI2C with SDA and SCL, plus VSEL pins for a hardware set voltage
Output dischargeInternal discharge of the output when the converter is disabled
Inductor0.47 microhenry for this member, 1.0 microhenry in the lower current application circuit
PackageYCH chip scale body, junction range covered by the family tables

What a software controlled rail needs from the board

The I2C address and the VSEL pins are both decoded at start up, and the two have to agree with what the system expects. A board that relies on the default register value comes up at the default voltage, and if the VSEL resistor was populated for a different rail the part settles at whichever setting the pins select. The first thing to check on a returned board is therefore the state of the VSEL pins, not the register map.

The 4 MHz capability is there for a reason. At 4 MHz the inductor can be 0.47 microhenry and the output capacitor can stay small, which keeps a core rail within a couple of millimetres of the processor it feeds. The cost is switching loss and a tighter requirement on the input capacitor, because the current pulses are shorter and the loop area starts to matter more than the capacitance value.

Output discharge is a small feature with a large effect on a multi rail board. When the converter is disabled, the part pulls the output down through an internal switch, so a rail does not sit at a residual voltage that back feeds an input protection diode on a device that is being powered down. On a board with four rails and a defined power down order, that behaviour is what keeps the sequence from latching a device into an unintended state.

Where this part fits

Processor core rails that change voltage at run time, camera and display rails in a phone or a tablet, radio module supplies and any board where the rail level is a software decision. Our cross reference notes for the family are at power management cross reference and the substitution notes are at pin to pin cross reference.

What to check before a purchase order

Check the current class and the interface option together. The 0.6 A and the 1 A members share a document, a register map and, in the same package, a pinout, so the order code is the only place the current class appears. A board that was signed off at 1 A will run on the 0.6 A part until the processor takes its peak load, and then it will hiccup rather than fail cleanly.

Check that the reel carries a part programmed with the intended default voltage and I2C address. These are order options, not something the board can change, and a part with the wrong default settles at the wrong rail before the host has finished booting. The receipt check on the marking and the reel is at incoming inspection plan.

Questions that come up on this part

Can the output be changed while the load is running, is the usual question. It can, through the output register, and the converter moves to the new level with its own ramp rate rather than stepping, which is what a processor expects when it asks for a lower core voltage. A rail that must not move while a device is running needs the register write to be gated by the host, and that is a system decision rather than a converter behaviour.

The second question is whether the I2C bus can be left unconnected. It can, and the part then follows the VSEL pins, which is the configuration for a board that only needs a fixed rail. The bus pins must still be tied to a defined level rather than left floating, because a floating line on a live bus is a latch up risk on any device on that bus and not only on the converter.