Contact Us

TPS628601YCHR

Brand: Texas Instruments
Texas Instruments TPS628601YCHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS628601YCHR — Power Management & Signal Chain | Superb Automation

TPS628601YCHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS628601YCHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS628601YCHR: a 1 A step down converter with an I2C interface in a 0.35 mm pitch wafer scale body

TPS628601YCHR is a synchronous step down converter with a digital control interface and a second pin that switches between two output voltages in hardware in a WCSP (YCH) body of 8 pins. It takes 1.75 V to 5.5 V of input and delivers 1 A with a switching frequency up to 4 MHz, which is what keeps the inductor and the capacitors small enough for a 6 square millimetre solution. The output is adjustable from 0.4 V to 1.9875 V in 12.5 mV steps over the I2C bus, and a dedicated select pin toggles between two preset voltages without any bus traffic, which is how a processor moves between an idle and a boost level in a single GPIO. Quiescent current is 2.3 microamps, accuracy is 1 per cent, and power good is brought out as an open drain output.

Order code and package

TPS628601YCHRthe 1 A member in the 8 pin wafer scale body on a 0.35 mm pitch, which is the current rating the 6 square millimetre solution is quoted for
TPS628600the 0.6 A member of the same family, same body and same interface, which is the option when the load is a sensor hub or a low power microcontroller
I2C interfacethe bus sets the output voltage, the ramp speed and the enable, and reads back the power good state, so a firmware can change a rail without a hardware change
Select pina single GPIO switches between two preset voltages stored in the part, which is faster than a bus transaction and works before the bus is initialised
Power save modeautomatic at light load and forced PWM when the rail has to stay quiet, with the mode selected over the bus
Voltage range0.4 V to 1.9875 V in 12.5 mV steps, which covers core rails from a 0.5 V memory supply to a 1.8 V input rail

Electrical parameters that decide the application

Input voltage1.75 V to 5.5 V, so a 3.3 V bus, a 5 V bus and a single lithium cell are all inside the window
Output current1 A continuous on this member, with the low side switch limit setting the peak the inductor has to handle
Output voltage0.4 V to 1.9875 V in 12.5 mV steps over the bus, with two presets reachable from the select pin
Switching frequencyup to 4 MHz, which is the figure that makes a small inductor and a small output capacitor enough
Quiescent current2.3 microamps in power save mode, which is the figure that matters on a rail that idles rather than one that runs flat out
Accuracy1 per cent over the specified range, quoted in PWM mode rather than in power save mode where the ripple is larger
Referencean internal reference sets the whole range, so the accuracy figure applies to every voltage on the bus table rather than to one preset
Power goodan open drain output that follows the bus configuration, which lets the firmware know when the rail is inside its window before it releases a processor from reset
Ramp controlthe start up ramp rate is set over the bus, so a rail that has to come up slowly for an inrush limit is configured in firmware rather than with an external capacitor
Protectioncurrent limit on both switches, thermal shutdown and an undervoltage lockout, with the fault state readable over the bus
Body8 pins on a 0.35 mm pitch wafer scale body, with a height under 0.6 mm, which is what allows it to sit under a processor on the back of the board
External partsan inductor and two ceramic capacitors, laid out for 0201 components, which is where the 6 square millimetre figure comes from

Digital control, the select pin and the family members

TPS628601YCHRthis order code, the 1 A member in the 8 pin 0.35 mm pitch wafer scale body
TPS628600the 0.6 A member, same body and same bus interface, for a sensor hub or a low power microcontroller
Bus controlthe output voltage, ramp rate, mode and enable are all set over the bus, and the power good state is readable
Select pinswitches between two stored presets from a single GPIO, which works before the bus is initialised
Voltage range0.4 V to 1.9875 V in 12.5 mV steps, which covers a memory rail and an input rail with the same part
Quiescent current2.3 microamps in power save mode, higher in forced PWM where the ripple is lower
Assembly0.35 mm pitch needs a stencil and a reflow profile the board house has to know about before the first panel

Points to check before this part goes on a BOM

A bus controlled rail is a firmware decision, and it needs a fallback. If the rail voltage is set only over I2C, the processor cannot boot until the bus is up, and the bus cannot come up until the processor is out of reset. The select pin exists to break that loop: the part comes up at a preset voltage with no bus traffic, and the firmware changes the level once it is running.

The 12.5 mV step is finer than most rails need. Dynamic voltage scaling uses a handful of levels, not 127. The value of the fine step is that a rail can be trimmed to a measured optimum rather than to the nearest 50 mV, which on a core rail is a real power saving.

2.3 microamps is a power save figure. In forced PWM the quiescent current is higher and the efficiency at light load is lower, so a rail that idles at a few hundred microamps gains from power save and a rail that has to stay quiet pays for it. The choice is a bus setting, not a part number.

4 MHz is not free. The high frequency shrinks the inductor and the capacitors and raises the switching loss. On a 1 A rail from 5 V to 1 V the loss is acceptable; on a rail with a large step down ratio the efficiency at full load is lower than a 2 MHz part would give, and the thermal budget has to include it.

The select pin has two presets, not an arbitrary voltage. The two values are programmed over the bus and stored, so the hardware switch is limited to what the firmware has already written. A board that expects the select pin to choose between any two levels without configuration gets the part's default.

A wafer scale body changes the assembly process. The 0.35 mm pitch needs a stencil and a reflow profile that a 0.5 mm pitch part does not, and the board house has to know before the first panel. That is a process decision rather than a purchasing one, and it is cheaper to make it at the first prototype than at the first production run.

Dynamic voltage scaling in a battery powered product

A processor that runs at 1.8 V for a burst and at 0.9 V when idle saves more energy than any sleep mode, and the saving only becomes available when the core rail can be moved while the processor is running. A converter with a bus interface and a select pin makes that a firmware change, and the ramp rate control keeps the transition inside the processor's own specification.

The same mechanism is used on a radio module, where the power amplifier rail is raised for a transmit slot and lowered between slots. The select pin does that in a GPIO write, without waiting for a bus transaction, which is the difference between a rail that is ready when the slot starts and one that is still ramping.

What the small solution size actually costs

The 6 square millimetre figure is measured with 0201 passives and a small inductor, and it assumes the board house can place 0201 parts and a 0.35 mm pitch body. On a line that runs 0402 and 0.5 mm pitch, the same converter takes twice the area and the body needs a stencil change. The solution size is a property of the assembly process as much as of the part.

Where this order code fits

a processor core rail that has to move between voltage levels at runtime, or a battery powered module where the rail is trimmed in firmware and the board area is fixed Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the MCU Cross Reference page.

Questions buyers ask

How is the output voltage set? Over the I2C bus in 12.5 mV steps from 0.4 V to 1.9875 V, with two preset values also reachable from a single select pin without any bus traffic.

What current can it deliver? 1 A on this member and 0.6 A on the TPS628600, in the same body and with the same interface.

Can the rail come up without a bus transaction? Yes, the select pin brings the part up at a preset voltage, which is what allows a processor to boot before its own bus is initialised.

What is the quiescent current? 2.3 microamps in power save mode. Forced PWM raises that figure and lowers the ripple, and the mode is chosen over the bus.

Does it need an external compensation network? No, the loop is internal and the data sheet gives the inductor and capacitor values for each frequency and output range, so the external part count is one inductor and two capacitors.

How does SUPERB handle this line? The offer names the exact ordering string, the body and the date code, and states the packing, because the 0.6 A and 1 A members are the same body and interface and differ only inside the part number.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.